监测模块1900/65A172323-01

易卖工控网（www.ymgk.com）提供”监测模块1900/65A172323-01”，产品详情：品牌/厂家：BENTLY、型号：1900/65A 172323-01、成色：全新、货期：现货 1天内发货、保修：180天，更多产品详情就上易卖工控网。

NI SCXI-1600（部件号：776572-1600 ）具有 16 位 ADC，是一款用于 SCXI 的USB 数据采集模块(DAQ)。该模块是用于 SCXI 数字 I/O、开关、模拟输入和模拟输出模块的全功能控制和数据模块。它的采样率为 200 kS/s。用户可以将SCXI-1600安装在仪器信号调理扩展 (SCXI) 机箱中，并为安装在机箱中的所有其他模块提供时钟、校准和外部数字触发连接。使用此模块，用户可以将任何 SCXI 机箱转变为强大可靠的即插即用数据采集系统。

NI SCXI 1600接收来自其他模块的模拟信号，并通过USB端口数字化、放大和传输数据。它是容易配置和校准的设备之一，因为它没有跳线、电位计或 DIP 开关。通过将它连接到其他 SCXI 模块，该模块可以从 RTD、热电偶、应变计、电流源和电压采集多达 352 个模拟信号。

NI SCXI 1600兼容 USB，支持供电或热插入 USB 端口。对于与时间相关的功能，该数据采集模块使用了一个强大的系统定时控制器，称为 National Instruments DAQ-STC。

为了控制模拟输入，DAQ-STC 由三个时序组组成。该模块在前面板上配备了四个 LED。有一组绿色 LED 用于监控机箱的 V+ 和 V– 导轨。另外两个 LED 显示SCXI-1600 数据采集模块的活动和就绪状态。为了进行校准，该模块的前面板上还提供了一个专用的 BNC 连接器。

NI 设备使用 NIDAQmx 驱动软件运行，该软件与软件包/应用程序开发环境（如 LabVIEW、LabWIndows/CVI 或 Measurement Studio）兼容。建议预热时间为 30 分钟，并且每年至少应进行一次外部校准。NI 设备的物理尺寸为 7.2 x 6.8 x 1.2 英寸。National Instruments SCXI-1349 屏蔽电缆适配器NI SCXI-1600 (Part No.: 776572-1600) has a 16-bit ADC and is a USB data acquisition module (DAQ) for SCXI. This module is a full-function control and data module for SCXI digital I/O, switch, analog input and analog output modules. Its sampling rate is 200 kS/s. Users can install the SCXI-1600 in the instrument signal conditioning expansion (SCXI) chassis, and provide clock, calibration and external digital trigger connection for all other modules installed in the chassis. With this module, users can transform any SCXI chassis into a powerful and reliable plug-and-play data acquisition system.



NI SCXI 1600 receives analog signals from other modules and digitizes, amplifies and transmits data through USB ports. It is one of the most easily configured and calibrated devices because it has no jumpers, potentiometers or DIP switches. By connecting it to other SCXI modules, the module can collect up to 352 analog signals from RTD, thermocouple, strain gauge, current source and voltage.



NI SCXI 1600 is compatible with USB and supports power supply or hot plugging into USB ports. For time-related functions, the data acquisition module uses a powerful system timing controller called National Instruments DAQ-STC.



In order to control the analog input, DAQ-STC consists of three timing groups. The module is equipped with four LEDs on the front panel. There is a set of green LEDs for monitoring the V+and V – rails of the chassis. The other two LEDs display the active and ready status of the SCXI-1600 data acquisition module. For calibration, a special BNC connector is also provided on the front panel of the module.



NI devices run using NIDAQmx driver software, which is compatible with software package/application development environment (such as LabVIEW, LabWIndows/CVI or Measurement Studio). The recommended warm-up time is 30 minutes, and external calibration should be carried out at least once a year. The physical size of the NI device is 7.2 x 6.8 x 1.2 inches. National Instruments SCXI-1349 shielded cable adapter



SCXI - 1349 (Part No.: 182671-01) was created for connecting the SCXI system to the data acquisition equipment. The SCXI - 1349 cable adapter connects the 68-pin E-series DAQ device (excluding the 61XXE model) to the SCXI module (excluding the SCXI switch module). This model has three connectors. First, there is a 68-pin male connector on the front panel. Next, there is a 50-pin centimeter connector on the printed circuit board. Finally, on the back of the adapter, there is a 50-pin bracket to install the female connector.



The US National Instrument SCXI-1349 requires several items: a computer, a 68-pin E-series DAQ device, a SCXI-1000, SCXI-1001 or SCXI-1000DC chassis, at least one SCXI module (not the SCXI switch module), a small slotted screwdriver, installation guide and NI SCXI-1349 shielded cable assembly, which consists of cable adapter and 68-pin shielded cable. The SCXI - 1349 can be used with 1 m or 2 m SH68-68-EP shielded cable to connect the E series equipment to the SCXI chassis. The other option is to use 0.5 m or 1 m SHC68-68-EP cable or 1 m PSHR68-68 cable to connect the DAQCard to the SCXI chassis. The maximum operating voltage of SCXI - 1349 is 30 Vrms, 42 Vpk or 60 VDC (signal+common mode).



The user must ensure that each signal connection is insulated to the maximum voltage that NI SCXI 1349 may encounter. Grounding power signals and other connections that exceed the maximum signal rating of the National Instruments SCXI-1349 cable adapter may cause electric shock or fire hazard. This can also damage the circuit board connected to the SCXI chassis, computer or SCX device.



The recommended operating temperature range of NI equipment is 0 to 50 ° C, the storage temperature range is – 20 to 70 ° C, and the non-condensing relative humidity range is 10 to 90%. Its design conforms to IEC 61010-1, UL 3111-1 and CAN/CSA C22.2 No. 1010.1 of electrical measurement and test equipment. National Instruments SCXI-1346 Multi-Chassis Cable Adapter



SCXI - 1346 (Part No.: 776574-46) is suitable for applications involving multiple chassis SCXI, because it can connect them to a DAQ device. This cable adapter has two cable connections. One connection is used for the signal from the digitizer or the previous SCXI chassis, while the second connection is used to route the signal from the digitizer to the subsequent chassis. SH68-68 - EP (Part No.: 184749-01, 1 m cable; 184749-02, 2 m cable; 184749-05, 5 m cable; or 184749-10, 10 m cable) can be purchased separately and with NI SCXI 1346. This cable adapter has a mounting bracket that can be reliably connected to the SCXI chassis.



The SCXI 1346 has four connectors. The first connector is the 68-pin male connector on the front panel, which is printed with To Next Chassis. The next connector is another 68-pin male connector on the front panel, which is printed with From DAQ Board or Previous Chassis. The third connector is the 50-pin centimeter connector on the printed circuit board. The last connector is also a 50-pin connector, but it is the bracket mounting female on the back of the cable adapter.



Using NI SCXI 1346 in a multi-chassle system requires the following items: a computer, a small flat-head screwdriver, a 68-pin shielded cable, a 68-pin E-series DAQ device, a SCXI 1001 or SCXI 1000 chassis (version K or later), one or more SCXI modules per chassis (excluding SCXI-1127, SCXI-1190 and SCXI-1191), SCXI 1349 shielded cable assembly, and SCXI-1346 installation guide. Users should keep in mind that the total cable length used in the multi-case SCXI system should not exceed 10 m. This will help ensure reliable operation.



SCXI 1346 runs with NI-DAQmx driver software compatible with the package/application development environment (ADE), such as LabVIEW, LabWindows, LabVIEW SignalExpress, Measurement Studio, Visual C++, or Visual Basic. You can use the National Instruments Measurement&Automation Explorer (MAX) tool to configure the device hardware.