WZ10-102837-505473模块备件

UO1200PMCX-DS1CEI-501818 

 easily
controlled by varying the armature current and by keeping the
magnetising current constant.
The advantage of DC drives is that speed and torque - the two
main concerns of the end-user - are controlled directly through
armature current: that is the torque is the inner control loop and
the speed is the outer control loop (see Figure 1).
Advantages
– Accurate and fast torque control
– High dynamic speed response
– Simple to control
Initially, DC drives were used for variable speed control because
they could easily achieve a good torque and speed response
with high accuracy.
10 Direct torque control | Technical guide No. 1
A DC machine is able to produce a torque that is:
– Direct - the motor torque is proportional to the armture
current: the torque can thus be controlled directly and
accurately.
– Rapid - torque control is fast; the drive system can have
a very high dynamic speed response. Torque can be
changed instantaneously if the motor is fed from an ideal
current source. A voltage fed drive still has a fast
response, since this is determined only by the rotor’s
electrical time constant (ie, the total inductance and
resistance in the armature circuit)
– Simple - field orientation is achieved using a simple
mechanical device called a commutator/brush assembly.
Hence, there is no need for complex electronic control
circuitry, which would increase the cost of the motor
controller.
Drawbacks
– Reduced motor reliability
– Regular maintenance
– Motor costly to purchase
– Needs encoder for feedback
The main drawback of this technique is the reduced reliability
of the DC motor; the fact that brushes and commutators wear
down and need regular servicing; that DC motors can be costly
to purchase; and that they require encoders for speed and position feedback.
While a DC drive produces an easily controlled torque from zero
to base speed and beyond, the motor’s mechanics are more
complex and require regular maintenance.
AC drives - Introduction
– Small size
– Robust
– Simple in design
– Light and compact
– Low maintenance
– Low cost
The evolution of AC variable speed drive technology has been
partly driven by the desire to emulate the performance of the
DC drive, such as fast torque response and speed accuracy,
while utilising the advantages offered by the standard AC motor.
Evolution of direct torque control
Technical guide No. 1 | Direct torque control 11
1
AC drives -Frequency control using PWM
Figure 2: Control loop of an AC drive with frequency control
using PWM
Features
– Controlling variables are voltage and frequency
– Simulation of variable AC sine wave using modulator
– Flux provided with constant V/f ratio
– Open-loop drive
– Load dictates torque level
Unlike a DC drive, the AC drive frequency control technique
uses parameters generated outside of the motor as controlling
variables, namely voltage and frequency.
Both voltage and frequency reference are fed into a modulator
which simulates an AC sine wave and feeds this to the motor’s
stator windings. This technique is called pulse width modulation
(PWM) and utilises the fact that there is a diode rectifier towards
the mains and the intermediate DC voltage is kept constant.
The inverter controls the motor in the form of a PWM pulse train
dictating both the voltage and frequency.
Significantly, this method does not use a feedback device which
takes speed or position measurements from the motor’s shaft
and feeds these back into the control loop.
Such an arrangement, without a feedback device, is called an
“open-loop drive”.
Evolution of direct torque control
12 Direct torque control | Technical guide No. 1
Advantages
– Low cost
– No feedback device required - simple
Because there is no feedback device, the controlling principle
offers a low cost and simple solution to controlling economical
AC induction motors.
This type of drive is suitable for applications which do not require
high levels of accuracy or precision, such as pumps and fans.
Drawbacks
– Field orientation not used
– Motor status ignored
– Torque is not controlled
– Delaying modulator used
With this technique, sometimes known as scalar control, field
orientation of the motor is not used. Instead, frequency and voltage are the main control variables and are applied to the stator
windings. The status of the rotor is ignored, meaning that no
speed or position signal is fed back.
Therefore, torque cannot be controlled with any degree of accuracy. Furthermore, the technique uses a modulator which
basically slows down communication between the incoming
voltage and frequency signals and the need for the motor to
respond to this changing signal.
AC drives - Flux vector control using PWM
Figure 3: Control loop of an AC drive with flux vector control using PWM
Features
– Field-oriented control - simulates DC drive
– Motor electrical characteristics are simulated - “ motor model”
– Closed-loop drive
– Torque controlled INDIRECTLYTo emulate the magnetic operating conditions of a DC motor,
ie, to perform the field orientation process, the flux-vector drive
needs to know the spatial angular position of the rotor flux inside
the AC induction motor.
With flux vector PWM drives, field orientation is achieved by electronic means rather than the mechanical commutator/brush
assembly of the DC motor.
Firstly, information about the rotor status is obtained by feeding back
rotor speed and angular position relative to the stator field by
means of a pulse encoder. A drive that uses speed encoders is
referred to as a “closed-loop drive”.
Also the motor’s electrical characteristics are mathematically
modelled with microprocessors used to process the data.
The electronic controller of a flux-vector drive creates electrical
quantities such as voltage, current and frequency, which are the
controlling variables, and feeds these through a modulator to the
AC induction motor. Torque, therefore, is controlled INDIRECTLY.
Advantages
– Good torque response
– Accurate speed control
– Full torque at zero speed
– Performance approaching DC drive
Flux vector control achieves full torque at zero speed, giving it
a performance very close to that of a DC drive.
Drawbacks
– Feedback is needed
– Costly
– Modulator needed
To achieve a high level of torque response and speed accuracy,
a feedback device is required. This can be costly and also adds
complexity to the traditional simple AC induction motor.
Also, a modulator is used, which slows down communication
between the incoming voltage and frequency signals and the
need for the motor to respond to this changing signal.
Although the motor is mechanically simple, the drive is electrically complex.
Evolution of direct torque control
14 Direct torque control | Technical guide No. 1
AC drives - Direct torque control
Figure 4: Control loop of an AC drive using DTC
Controlling variables
With the revolutionary DTC technology developed by ABB, field
orientation is achieved without feedback using advanced motor
theory to calculate the motor torque directly and without using
modulation. The controlling variables are motor magnetising
flux and motor torque.
With DTC there is no modulator and no requirement for a tachometer or position encoder to feed back the speed or position
of the motor shaft.
DTC uses the fastest digital signal processing hardware available and a more advanced mathematical understanding of how
a motor works.
The result is a drive with a torque response that is typically 10
times faster than any AC or DC drive. The dynamic speed accuracy of DTC drives will be 8 times better than any open loop
AC drives and comparable to a DC drive that is using feedback.
DTC produces the first “universal” drive with the capability to
perform like either an AC or DC drive.
The remaining sections in this guide highlight the features and
advantages of DTC.
Evolution of direct torque control
Technical guide No. 1 | Direct torque control 15
1
Comparison of variable speed drives
Let us now take a closer look at each of these control blocks
and spot a few differences.
Figure 1: Control loop of a DC
drive
Figure 2: Control loop with
frequency control
Figure 3: Control loop with flux
vector control
Figure 4 Control loop of an AC
drive using DTC
The first observation is the similarity between the control block of
the DC drive (Figure 1) and that of DTC (Figure 4).
Both are using motor parameters to directly control torque.
But DTC has added benefits including no feedback device is
used; all the benefits of an AC motor (see page 10); and no
external excitation is needed.
Table 1: Comparison of control variables
Evolution of direct torque control
16 Direct torque control | Technical guide No. 1
As can be seen from table 1, both DC drives and DTC drives use
actual motor parameters to control torque and speed. Thus, the
dynamic performance is fast and easy. Also with DTC, for most
applications, no tachometer or encoder is needed to feed back
a speed or position signal.
Comparing DTC (Figure 4) with the two other AC drive control
blocks (Figures 2 & 3) shows up several differences, the main
one being that no modulator is required with DTC.
With PWM AC drives, the controlling variables are frequency and
voltage which need to go through several stages before being
applied to the motor. Thus, with PWM drives control is handled
inside the electronic controller and not inside the motor.
Evolution of direct torque control
Technical guide No. 1 | Direct torque control 17
1
Chapter 3 - Questions and answers
General
What is direct control?
Direct torque control - or DTC as it is called - is the very latest
AC drive technology developed by ABB and is set to replace
traditional PWM drives of the open- and closed-loop type in the
near future.
Why is it called direct torque control?
Direct torque control describes the way in which the control of
torque and speed are directly based on the electromagnetic state
of the motor, similar to a DC motor, but contrary to the way in
which traditional PWM drives use input frequency and voltage.
DTC is the first technology to control the “real” motor control
variables of torque and flux.
What is the advantage of this?
Because torque and flux are motor parameters that are being
directly controlled, there is no need for a modulator, as used in
PWM drives, to control the frequency and voltage. This, in effect,
cuts out the middle man and dramatically speeds up the response
of the drive to changes in required torque. DTC also provides
precise torque control without the need for a feedback device.
Why is there a need for another AC drive technology?
DTC is not just another AC drive technology. Industry is demanding more and existing drive technology cannot meet these
demands.
For example, industry wants:
– Better product quality which can be partly achieved with
improved speed accuracy and faster torque control.
– Less down time which means a drive that will not trip unnecessarily; a drive that is not complicated by expensive
feedback devices; and a drive which is not greatly affected
by interferences like harmonics and RFI.
– Fewer products. One drive capable of meeting all appliction
needs whether AC, DC or servo. That is a truly “universal”
drive.
– A comfortable working environment with a drive that produces much lower audible noise.
18 Direct torque control | Technical guide No. 1
These are just some of the demands from industry. DTC can
deliver solutions to all these demands as well as bringing new
benefits to many standard applications.
Who invented DTC?
ABB has been carrying out research into DTC since 1988 foll owing the publication of the theory in 1971 and 1985 by German
doctor Blaschke and his colleague Depenbrock. DTC leans on
the theory of field oriented control of induction machines and
the theory of direct self control. ABB has spent over 100 man
years developing the technology.
Performance
What are the main benefits of DTC technology over traditional AC drive
technology?
There are many benefits of DTC technology. But most significantly, drives using DTC technology have the following exceptional dynamic performance features, many of which are obtained
without the need for an encoder or tachometer to monitor shaft
position or speed:
– Torque response: - How quickly the drive output can reach
the specified value when a nominal 100 percent torque reference step is applied.
For DTC, a typical torque response is 1 to 2 ms below 40 Hz
compared to between 10-20 ms for both flux vector and DC
drives fitted with an encoder. With open loop PWM drives (see
page 11) the response time is typically well over 100 ms. In
fact, with its torque response, DTC has achieved the natural
limit. With the voltage and current available, response time
cannot be any shorter. Even in the newer “sensorless” drives
the torque response is hundreds of milliseconds.
– Accurate torque control at low frequencies, as well as full
load torque at zero speed without the need for a feedback
device such as an encoder or tachometer. With DTC, speed
can be controlled to frequencies below 0.5 Hz and still provide
100 percent torque right the way through to zero speed.
– Torque repeatability: - How well the drive repeats its output torque with the same torque reference command. DTC,
without an encoder, can provide 1 to 2 percent torque repeatability of the nominal torque across the speed range. This is
half that of other open-loop AC drives and equal to that of
closed-loop AC and DC drives.
Questions and answers
Technical guide No. 1 | Direct torque control 19
1
– Motor static speed accuracy: - Error between speed reference and actual value at constant load. For DTC, speed
accuracy is 10 percent of the motor slip, which with an 11
kW motor, equals 0.3 percent static speed accuracy. With
a 110 kW motor, speed accuracy is 0.1 percent without encoder (open-loop). This satisfies the accuracy requirement
or 95 percent of industrial drives applications. However, for
the same accuracy from DC drives an encoder is needed.
In contrast, with frequency controlled PWM drives, the
static speed accuracy is typically between 1 to 3 percent.
So the potential for customer process improvements is significantly higher with standard drives using DTC technology.
A DTC drive using an encoder with 1024 pulses/revolution
can achieve a speed accuracy of 0.01 percent.
– Dynamic speed accuracy: - Time integral of speed deviation when a nominal (100 percent) torque speed is applied.
DTC open-loop dynamic speed accuracy is between 0.3
to 0.4%sec. This depends on the gain adjustment of the
controller, which can be tuned to the process requirements.
With other open-loop AC drives, the dynamic accuracy is eight
times less and in practical terms around 3%sec.If we furnish
the DTC controller with an encoder, the dynamicspeed accuracy will be 0.1%sec, which matches servo drive performance.
What are the practical benefits of these performance figures?
– Fast torque response: - This significantly reduces the speed
drop time during a load transient, bringing much improved
process control and a more consistent product quality.
– Torque control at low frequencies: - This is particularlybeneficial to cranes or elevators, where the load needs to be
started and stopped regularly without any jerking. Also with
a winder, tension control can be achieved from zero through
to maximum speed. Compared to PWM flux vector drives,
DTC brings the cost saving benefit that no tachometer is
needed.
– Torque linearity: - This is important in precision applications
like winders, used in the paper industry, where an accurate
and consistent level of winding is critical.
– Dynamic speed accuracy: - After a sudden load change, the
motor can recover to a stable state remarkably fast.
Questions and answers
20 Direct torque control | Technical guide No. 1
Table 2: Dynamic performance features and benefits offered by DTC
technology
Apart from excellent dynamic performance figures, are there any other
benefits of DTC drive technology?
Yes, there are many benefits. For example, DTC drives do not
need a tachometer or encoder to monitor motor shaft speed
or position in order to achieve the fastest torque response ever
from an AC drive. This saves initial cost.
Investment cost
savings. Increased
reliability. Better
process control.
Higher product
quality. Leads to a
true universal drive.
Similar performance
to DC but without
tachometer. Reduced
mechanical failures
for machinery. Less
downtime. Lower
investment.
Cost effective, high
performance torque
drive; provides
position control
and better static
accuracy. High
accuracy control with
standard AC motor.
Investment cost
saving. Better
load control. Can
use AC drive and
motor instead of
DC. Standard AC
motor means less
maintenance and
lower cost.
Allows speed to be
controlled better than
0.5 percent accuracy.
No tachometer needed
in 95 percent of all
applications.
Drive for demanding
applications. Allows
required torque at
all times. Torque
repeatability 1 percent.
Torque response time
less than 5ms.
No mechanical brake
needed. Smooth
transition between
drive and brake. Allows
drive to be used in
traditional DC drive
applications.
Servo drive
performance.
Good motor speed
accuracy without
tachometer.
Excellent torque
control without
tachometer.
Control down to zero
speed and position
with encoder.
Full torque at zero
speed with or without
tachometer/ encoder.
FEATURE RESULT BENEFIT
Questions and answers
Technical guide No. 1 | Direct torque control 21
1
Rapid control DC link
voltage.
Power loss ride through. Drive will not trip. Less
down time. Avoids
process interruptions.
Less waste in continuous
process.
Automatic start
(Direct restart).
Starting with motor
residual inductance
present. No restarting
delay required.
Can start into a motor
that is running without
waiting for flux to decay.
Can transfer motor from
line to drive. No restart.
No interruptions on
process.
Controlled braking
between two speed
points.
Investment cost savings.
Better process control.
No delay required as
in DC braking. Can be
used for decelerating to
other than zero speed.
Reduced need for brake
chopper and resistor.
Flux braking.
Flux optimization. Motor losses minimised.
Less motor noise.
Controlled motor.
Self identification/
Auto-tuning.
Tuning the motor to drive
for top performance.
Easy and accurate
setup. No parameter
tuning required. Less
commissioning time.
Guaranteed starting
torque. Easy retrofit for
any AC system.
No predetermined
switching pattern of
power devices.
Low noise. No fixed
carrier, therefore
acoustic noise
reasonable due to
“white” noise spectrum.
Cost savings in acoustic
barriers in noise sensitive
applications. No harmful
mechanical resonances.
Lower stresses in
gearboxes, fans, pumps.
Can accelerate and
decelerate in quickest
time possible without
mechanical constraints.
Automatic start
(Flying start).
Synchronises to rotating
motor.
No process interruptions.
Smooth control of
machinery. Resume
control in all situations.
No limits on maximum
acceleration and
deceleration rate.
Better process control.
FEATURE RESULT BENEFIT
Table 3: User features and benefits offered by DTC technology
Questions and answers
22 Direct torque control | Technical guide No. 1
Also a DTC drive features rapid starting in all motor electromagnetic and mechanical states. The motor can be started
immediately without delay.
It appears that DTC drives are most advantageous for high performance
or demanding drive applications. What benefits does DTC bring to
standard drives?
Standard applications account for 70 percent of all variable speed
drives installed throughout industry. Two of the most common
applications are in fans and pumps in industries like heating, ventilating and air conditioning ( HVAC), water and food and drinks.
In these applications, DTC provides solutions to problems like
harmonics and noise.
For example, DTC technology can provide control to the drive
input line generating unit, where a conventional diode bridge is
replaced with a controlled bridge.
This means that harmonics can be significantly reduced with
a DTC controlled input bridge. The low level current distortion
with a DTC controlled bridge will be less than a conventional
6-pulse or 12-pulse configuration and power factor can be as
high as 0.99.
For standard applications, DTC drives easily withstand huge and
sudden load torques caused by rapid changes in the process,
without any overvoltage or overcurrent trip.
Also, if there is a loss of input power for a short time, the drive
must remain energised. The DC link voltage must not drop below
the lowest control level of 80 percent. To ensure this, DTC has
a 25 microseconds control cycle.
What is the impact of DTC on pump control?
DTC has an impact on all types of pumps. Because DTC leads
to a universal drive, all pumps, regardless of whether they are
centrifugal or constant torque type (screw pumps) can now be
controlled with one drive configuration, as can aerators and
conveyors. DTC technology allows a drive to adjust itself to
varying application needs.
For example, in screw pumps a drive using DTC technology
will be able to adjust itself for sufficient starting torque for a
guaranteed start.
Questions and answers
Technical guide No. 1 | Direct torque control 23
1
Improved power loss ride through will improve pumping availability during short power breaks.
The inherent torque control facility for DTC technology allows
the torque to be limited in order to avoid mechanical stress on
pumps and pipelines.
What is the impact of DTC technology on energy savings?
A feature of DTC which contributes to energy efficiency is a
development called motor flux optimization.
With this feature, the efficiency of the total drive (that is controller
and motor) is greatly improved in fan and pump applications.
For example, with 25 percent load there is up to 10 percent total
energy efficiency improvement. At 50 percent load there can be
2 percent total efficiency improvement.
This directly impacts on operating costs. This feature also significantly reduces the motor noise compared to that generated
by the switching frequency of a traditional PWM drive.
Has DTC technology been used in many installations?
Yes, there are hundreds of thousands of installations in use. For
example, one of the world’s largest web machine manufacturers
tested DTC technology for a winder in a film finishing process.
The Requirement:
Exact torque control in the winder so as to produce high quality
film rolls.
The Solution:
Open-loop DTC drives have replaced traditional DC drives and
latter flux vector controlled AC drives on the centre drives in the
rewind station.
The Benefits:
Winder station construction simplified and reliability increased.
The cost of one tachometer and associated wiring equals that
of one 30 kW AC motor. This provides significant investment
cost savings.
Questions and answers
24 Direct torque control | Technical guide No. 1
Operation
What is the difference between DTC and traditional PWM methods?
– Frequency control PWM and flux vector PWM
Traditional PWM drives use output voltage and output frequency as the primary control variables but these need to be
pulse width modulated before being applied to the
motor.
This modulator stage adds to the signal processing time and
therefore limits the level of torque and speed response
possible from the PWM drive.
Typically, a PWM modulator takes 10 times longer than DTC to
respond to actual change.
– DTC control
DTC allows the motor’s torque and stator flux to be used as
primary control variables, both of which are obtained directly
from the motor itself. Therefore, with DTC, there is no need for
a separate voltage and frequency controlled PWM modulator.
Another big advantage of a DTC drive is that no feedback device
is needed for 95 percent of all drive applications.
Why does DTC not need a tachometer or position encoder to tell it
precisely where the motor shaft is at all times?
There are four main reasons for this:
– The accuracy of the motor model (see page 29).
– Controlling variables are taken directly from the motor (see
page 29).
– The fast processing speeds of the DSP and optimum pulse
selector hardware (see page 30).
– No modulator is needed (see page 14).
Questions and answers
Technical guide No. 1 | Direct torque control 25
1
When combined to form a DTC drive, the above features produce a drive capable of calculating the ideal switching voltages
40,000 times every second. It is fast enough to control individual
switching pulses. Quite simply, it is the fastest ever achieved.
Once every 25 microseconds, the inverter’s semiconductors are
supplied with an optimum switching pattern to produce the
required torque. This update rate is substantially less than any
time constants in the motor. Thus, the motor is now the limiting
component, not the inverter.
What is the difference between DTC and other sensorless drives on the
market?
There are vast differences between DTC and many of the sensorless drives. But the main difference is that DTC provides accurate
control even at low speeds and down to zero speed without
encoder feedback. At low frequencies the nominal torque step
can be increased in less than 1ms. This is the best available.
How does a DTC drive achieve the performance of a servo drive?
Quite simply because the motor is now the limit of performance
and not the drive itself. A typical dynamic speed accuracy for
a servo drive is 0.1%s. A DTC drive can reach this dynamic
accuracy with the optional speed feedback from a tachometer.
How does DTC achieve these major improvements over traditional
technology?
The most striking difference is the sheer speed by which DTC
operates. As mentioned above, the torque response is the
quickest available.
To achieve a fast torque loop, ABB has utilised the latest high
speed signal processing technology and spent 100 man years
developing the highly advanced motor model which precisely
simulates the actual motor parameters within the controller.
For a clearer understanding of DTC control theory, see
page 28.
Questions and answers
26 Direct torque control | Technical guide No. 1
Does a DTC drive use fuzzy logic within its control loop?
No. Fuzzy logic is used in some drives to maintain the acceleration current within current limits and therefore prevent the drive
from tripping unnecessarily. As DTC is controlling the torque
directly, current can be kept within these limits in all operating
conditions.
A drive using DTC technology is said to be tripless. How has this been
achieved?
Many manufacturers have spent years trying to avoid trips during
acceleration and deceleration and have found it extraordinarily
difficult. DTC achieves tripless operation by controlling the actual
motor torque.
The speed and accuracy of a drive which relies on computed rather
than measured control parameters can never be realistic. Unless you are
looking at the shaft, you are not getting the full picture. Is this true with
DTC?
DTC knows the full picture. As explained above, thanks to the sophistication of the motor model and the ability to carry out 40,000
calculations every second, a DTC drive knows precisely what the
motor shaft is doing. There is never any doubt as to the motor’s
state. This is reflected in the exceptionally high torque response
and speed accuracy figures quoted on pages 18 and 19.
Unlike traditional AC drives, where up to 30 percent of all switchings are wasted, a drive using DTC technology knows precisely
where the shaft is and so does not waste any of its switchings.
DTC can cover 95 percent of all industrial applications. The
exceptions, mainly applications where extremely precise speed
control is needed, will be catered for by adding a feedback device to provide closed loop control. This device, however, can
be simpler than the sensors needed for conventional closed
loop drives.
Even with the fastest semiconductors some dead time is introduced.
Therefore, how accurate is the auto-tuning of a DTC drive?
Auto-tuning is used in the initial identification run of a DTC drive
(see page 29). The dead time is measured and is taken into account by the motor model when calculating the actual flux. If we
compare to a PWM drive, the problem with PWM is in the range
20 to 30 Hz which causes torque ripple.
Questions and answers
Technical guide No. 1 | Direct torque control 27
1
What kind of stability will a DTC drive have at light loads and low speeds?
The stability down to zero speed is good and both torque and
speed accuracy can be maintained at very low speeds and light
loads. We have defined the accuracies as follows:
Torque accuracy: Within a speed range of 2 to 100 percent
and a load range of 10 to100 percent, the torque accuracy is
2 percent.
Speed accuracy: Within a speed range of 2 to 100 percent and
a load range of 10 to 100 percent, the speed accuracy is 10
percent of the motor slip. Motor slip of a 37 kW motor is about
2 percent which means a speed accuracy of 0.2 percent.
What are the limitations of DTC?
If several motors are connected in parallel in a DTC-controlled inverter, the arrangement operates as one large motor. It has no
information about the status of any single motor. If the number
of motors varies or the motor power remains below 1/8 of the
rated power, it would be best to select the scalar control macro.
Can DTC work with any type of induction motor?
Yes, any type of asynchronous, squirrel cage motor.
Questions and answers
28 Direct torque control | Technical guide No. 1
Chapter 4 - Basic control theory
How DTC works
Figure 5, below, shows the complete block diagram for direct
torque control ( DTC).
Walk around the block
Figure 5: DTC comprises two key blocks: Speed control and torque
control
The block diagram shows that DTC has two fundamental sections: the torque control loop and the speed control loop. Now
we will walk around the blocks exploring each stage and showing
how they integrate together.
Let’s start with DTC’s torque control loop.
Technical guide No. 1 | Direct torque control 29
1
Torque control loop
Step 1 Voltage and current measurements
In normal operation, two motor phase currents and the DC bus
voltage are simply measured, together with the inverter’s switch
positions.
Step 2 Adaptive motor model
The measured information from the motor is fed to the Adaptive
motor model.
The sophistication of this motor model allows precise data about
the motor to be calculated. Before operating the DTC drive, the
motor model is fed information about the motor, which is collected
during a motor identification run. This is called auto-tuning and
data such as stator resistance, mutual inductance and saturation
coefficients are determined along with the motor’s inertia. The
identification of motor model parameters can be done without
rotating motor shaft. This makes it easy to apply DTC technology also in retrofits. The extremely fine tuning of motor model is
achieved when the identification run also includes running the
motor shaft for some seconds.
There is no need to feed back any shaft speed or position with
tachometers or encoders if the static speed accuracy requirement is over 0.5 percent, as it is for most industrial applications.
Basic control theory
30 Direct torque control | Technical guide No. 1
This is a significant advance over all other AC drive technology.
The motor model is, in fact, key to DTC’s unrivalled low speed
performance.
The motor model outputs control signals which directly represent
actual motor torque and actual stator flux. Also shaft speed is
calculated within the motor model.
Step 3 Torque comparator and flux comparator
The information to control power switches is produced in the
torque and flux comparator.
Both actual torque and actual flux are fed to the comparators
where they are compared, every 25 microseconds, to a torque
and flux reference value. Torque and flux status signals are calculated using a two level hysteresis control method.
These signals are then fed to the optimum pulse selector.
Step 4 Optimum pulse selector
Within the optimum pulse selector is the latest 40 MHz digital
signal processor ( DSP) together with ASIC hardware to determine
the switching logic of the inverter. Furthermore, all control signals
are transmitted via optical links for high speed data transmission.
This configuration brings immense processing speed such that
every 25 microseconds the inverter’s semiconductor switching
devices are supplied with an optimum pulse for reaching, or
maintaining, an accurate motor torque.
The correct switch combination is determined every control
cycle. There is no predetermined switching pattern. DTC has
been referred to as “just-in-time” switching, because, unlike
traditional PWM drives where up to 30 percent of all switch
changes are unnecessary, with DTC each and every switching
is needed and used.
This high speed of switching is fundamental to the success of
DTC. The main motor control parameters are updated 40,000
times a second. This allows extremely rapid response on the
shaft and is necessary so that the motor model (see step 2) can
update this information.
It is this processing speed that brings the high performance figures including a static speed control accuracy, without encoder,
of ±0.5 percent and the torque response of less than 2 ms.
Basic control theory
Technical guide No. 1 | Direct torque control 31
1
Speed control
Step 5 Torque reference controller
Within the torque reference controller, the speed control output
is limited by the torque limits and DC bus voltage.
It also includes speed control for cases when an external torque
signal is used. The internal torque reference from this block is
fed to the torque comparator.
Step 6 Speed controller
The speed controller block consists both of a PID controller
and an acceleration compensator. The external speed reference
signal is compared to the actual speed produced in the motor
model. The error signal is then fed to both the PID controller and
the acceleration compensator. The output is the sum of outputs
from both of them.
Step 7 Flux reference controller
An absolute value of stator flux can be given from the flux reference controller to the flux comparator block. The ability to control
and modify this absolute value provides an easy way to realise
many inverter functions such as flux optimization and flux braking (see page 21).
Basic control theory
32 Direct torque control | Technical guide No. 1
Chapter 5 - Index
A
acceleration compensator 31
accuracy control 20
AC drive 1, 3, 7, 11, 12, 14, 15, 16, 17, 18,
19, 20, 23, 26, 30
AC drive using DTC 14, 15
AC drive with flux vector control 12
AC motor 20
aerators 22
air condition 22
ASIC 30
auto-tuning 21, 26, 29
B
Blaschke 18
braking 21, 31
C
closed-loop 12, 18
closed-loop drives 12
commissioning 21
control cycle 30
controlled input bridge 22
controlling variables 16
control loop 9, 11, 12, 14, 15, 26, 28, 29, 31
control variables 15, 24
conveyors 22
costs 20, 21, 23
D
DC bus voltage 29, 31
DC drive 9, 12, 15, 16, 20
DC link voltage 21, 22
DC motor 9
Depenbrock 18
diode bridge 22
direct torque control 8, 9, 10, 11, 12, 13, 14,
15, 16, 28
drive input line generating unit 22
DSP 24, 30
DTC 14, 15, 16, 18, 19, 20, 21, 22, 23, 24,
25, 26, 27, 28, 29, 30
dynamic speed accuracy 19, 25
E
electronic controller 16
elevators 19
encoders 16, 20, 24, 25, 29, 30
energy savings 23
external speed reference 31
external torque signal 31
F
fan 21, 22, 23
feedback device 18, 24, 26
field oriented control 18
film finishing 23
flux braking 21, 31
flux comparator 30, 31
flux optimization 21, 23, 31
flux reference controller 31
flux vector 12, 15, 18, 23, 24
flux vector control 12, 15
food 22
frequency control 11, 15, 24
fuzzy logic 26
G
gearbox 21
H
harmonics 22
heating 22
HVAC 22
hysteresis control 30
I
inertia 29
initial cost 20
L
load torque 18, 22
loss of input power 22
low frequencies 18, 19, 25
M
maintenance 20
mechanical brake 20
modulator 16, 24
motor flux optimization 23
motor model 12, 24, 25, 26, 29, 30, 31
motor noise 21, 23
motor static speed 19
motor torque 30
mutual inductance 29
N
noise 21, 22, 23
nominal torque step 25
O
operating cost 23
optical link 30
optimum pulse selector 30
output frequency 24
output voltage 24
P
paper industry 19
PID controller 31
pipelines 23
position control 20
position encoder 24
power factor 22
power loss ride through 21, 23
Technical guide No. 1 | Direct torque control 33
1
predetermined switching pattern 21, 30
pump 21, 22, 23
PWM 11, 12, 16, 18, 19, 23, 24, 26, 30
PWM AC drive 16, 23, 24, 26, 30
R
reliability 20
restart 21
retrofit 21
S
saturation coefficient 29
scalar control 27
sensorless 25
servo drive 20, 25
signal processing 24, 25
signal processing time 24
speed 8, 15, 16, 18, 19, 20, 21, 22, 24