KLA-Tencor-501529模块备件

易卖工控网（www.ymgk.com）提供”KLA-Tencor-501529模块备件”，产品详情：品牌/厂家：0040-32460-504815、型号：KLA-Tencor-501529、成色：全新、货期：现货 1天内发货、保修：180天，更多产品详情就上易卖工控网。

KLA-Tencor-501529
2.8一般特征
CS 31系统是根据国际标准IEC 1131-2开发的。
● 操作条件
–温度：
● 操作0°C…+55°C 32。。。131华氏度
● 存储-40°C…+75°C-40。。。167°F
● 运输-25°C…+75°C-13。。。167°F
-湿度符合DIN 40040 F级，无
冷凝：
● 全年平均75%
● 每年多30天95%
● 在其他日期
年份，有时为85%
–气压：
● 运行800 hPA（2000 m）
● 存储660 hPA（3500 m）
● 机械数据
–程度
防护IP 20
–外壳UL94 V0
UL94 V1适用于中央单元90级，
连接器07KPxx和装置ICDxx
–三者相互振动
垂直轴10 Hz。。。57赫兹
连续：0.0375 mm振幅
偶然：0.075 mm振幅
57赫兹。。。150赫兹
连续：0.5 g加速度
偶尔：1.0 g加速度
–冲击偶尔漂移至15 g，11 ms，
三个相互之间各有一个半正弦
垂直的轴
–对电源>30 VAC的装置的影响。
根据IEC 950：钢球承受
质量为500 g的试验应自由下落
从1300 mm的高度
● 安装
–DIN导轨35 mm
–螺钉Ø4 mm（M4）
安装
● 串行接口
–用于连接RS485，
使用螺旋端子的中央单元
远程装置
–用于编程和RS232-C
设置参数9极D连接器
（女性）
● 结束
–在插入式基座ECZ上，仅使用60°C铜导线
横截面：
–总线接线端子：双绞线
AWG 24（0.22 mm2
)至AWG 18（0.8 mm2
)
–接地端子：刚性或绞合连接器
AWG 10（5.2 mm2
)
–其他端子：
● 输入：绞合连接器
AWG 18（0.8 mm2
)至AWG 14（2.1 mm2
)
● 输出：绞合连接器
AWG 14（2.1 mm2
)
● 电源
AWG 14（2.1 mm2
)
–在可拆卸端子2.5 mm2（铜N°
AWG14）
块（小截面）
–可拆卸端子1.5 mm2（铜N°
AWG16）
块（小截面）
–拧紧7磅的螺钉。英寸（0.8牛米）
扭矩（仅供参考）
● 电源连接
–24 VDC（过程和24 VDC
电源（-20%，+25%，即19.2…30V）
包括波纹
纹波系数<5%
–120 VAC电源120 VAC
（-15%，+10%，即102…132V）
50 Hz或60 Hz（±5%）
–230 VAC电源230 VAC
（-15%，+10%，即195.5…253V）
50 Hz或60 Hz（±5%）
● 电压下降和中断
–直流电源中断时间10毫秒
两者之间的时间间隔
下降1s
–交流电源中断时间0.5周期
两者之间的时间间隔
下降1s
● 爬电距离和电气间隙
根据EN 61131-2/
IEC1131-2
● 绝缘测试电压
绝缘测试电压
符合IEC 1131-2
1系统描述2-14 ABB Procontic CS31/版本：04.96-FRCTL
● 电磁兼容性（EMC）
–静电放电（ESD）符合
IEC 1000-4-2
（严重级别3）
测试峰值电压：
● 通过空气放电时8 kV
● 出院时
通过继电器触点6 kV
两次放电之间的时间>1s
每次放电的次数
选定点10
–辐射电磁
现场抗扰度测试根据
IEC 1000-4-3
场强10伏/米
（严重级别3）
频率范围27 MHz至1000 MHz
扫描速度1.5 x 10E-3
十年/秒
–快速瞬变脉冲群测试（FTT），根据
IEC 1000-4-4
干扰电压：
电源端子115/230 V 2 kV
电源端子24 V 2 kV
输出端子24 V 1 kV
输出端子115/230 V 2 kV
输入端子24 V 1 kV
输入端子115/230 V 2 kV
模拟输入/输出端子1 kV
CS 31母线2 kV
编程接口0.5 kV
–浪涌抗扰度符合
IEC 1000-4-5
测试电压
非对称耦合共模
电源（115/230 VAC）2 kV
电源（24 VDC）1 kV
数字输入/输出1 kV
测试电压
对称耦合差模
电源（115/230 VAC）1 kV
电源（24 VDC）1 kV
数字输入/输出1 kV
● ABB Procontic CS 31系统总线
CS 31总线为屏蔽双绞线RS485
–交叉0.22。。。0.8 mm2
（编号：
AWG 24。。。编号°
AWG 18）
–扭转>10/m
–阻力100/km
–阻抗
特征100至150
–电容<150 nF/km
–防护罩
–终端120，1/4瓦
电阻器连接在
公共汽车的尽头
–点数
共31个从节点+1个主节点
1 ABB Procontic CS31/版本：04.96-FRCTL 3-1一般操作
3一般操作
3.1与远程装置的CPU通信
中央装置和远程装置之间的通信
单元无需用户干预，因为它是由
专用串行接口。
中央单元的双端口RAM支持数据传输
在用户程序处理器和专用
串行接口。
在读取周期中，从远程装置获取数据，并
通过总线存储在双端口RAM中，专用
串行接口，然后用户程序处理器读取
来自双端口RAM的数据。
类似地，数据从双端口RAM传输到
通过专用串行接口和总线的远程装置
wri
KLA-Tencor-501529

KLA-Tencor-501529
2.8 General characteristics The CS 31 system is developped according to the international standard IEC 1131-2. ● Operating conditions – Temperature : ● operation 0 °C ... + 55 °C 32 ... 131 °F ● storage - 40 °C ... + 75 °C - 40 ... 167 °F ● transport - 25 °C ... + 75 °C - 13 ... 167 °F – Humidity acc. to DIN 40040 class F without condensation : ● average over the year 75 % ● up to 30 days of a year 95 % ● on the other days withregard to the average of the year, occasionnally 85 % – Air pressure : ● operation 800 hPA ( 2000 m) ● storage 660 hPA ( 3500 m) ● Mechanical data – degree of protection IP 20 – housing UL94 V0 UL94 V1 for central units serie 90, coupler 07KPxx and units ICDxx – vibration each of three mutually perpendicular axes 10 Hz ...57 Hz continuous : 0.0375 mm amplitude occasional : 0.075 mm amplitude 57 Hz ... 150 Hz continuous : 0.5 g acceleration occasional : 1.0 g acceleration – shocks occasional excursion to 15 g, 11 ms, halfsine in each of three mutually perpendicular axes – impact for units with a power supply > 30 VAC. withstand According to IEC 950 : a steel sphere test with a mass of 500 g is to fall freely from a height of 1300 mm ● Mounting – DIN rail 35 mm – Screw screws Ø 4 mm (M4) mounting ● Serial interfaces – for connection of the RS485, central unit to using screw terminals the remote units – for programming and RS232-C setting parameter 9 pole D connector (female) ● Termination – on the plug-in base ECZ use 60 °C copper conductor only Cross section : – bus wiring terminal : twisted pair AWG 24 (0.22 mm2 ) to AWG 18 (0.8 mm2 ) – earth terminal : rigid or stranded connector AWG 10 (5.2 mm2 ) – Others terminals : ● inputs : stranded connector AWG 18 (0.8 mm2 ) to AWG 14 (2.1 mm2 ) ● outputs : stranded connector AWG 14 (2.1 mm2 ) ● power supply AWG 14 (2.1 mm2 ) – on removable terminal 2.5 mm2 (copper N° AWG14) block (small section) – on removable terminal 1.5 mm2 (copper N° AWG16) block (small section) – screws tightening 7 ibs. inch (0.8 Nm) torque (for guidance only) ● Supply connections – 24 VDC (process and 24 VDC power supply (-20 %, +25 %, i.e. 19.2 ... 30V) incl. ripple ripple factor < 5 % – 120 VAC power supply 120 VAC (-15%, +10%, i.e. 102 ... 132V) 50 Hz or 60 Hz (± 5 %) – 230 VAC power supply 230 VAC (-15%, +10%, i.e. 195.5 ... 253V) 50 Hz or 60 Hz (± 5 %) ● Voltage drops and interruptions – DC power supply interruption time 10 ms time interval between two drops 1s – AC power supply interruption time 0.5 period time interval between two drops 1s ● Creepage distances and clearances according to EN 61131-2 / IEC1131-2 ● Insulation test voltages the insulation test voltages are according to IEC 1131-2 1 System description 2 - 14 ABB Procontic CS31/Edition : 04.96 - FRCTL ● Electromagnetic compatibility (EMC) – electrostatic discharge (ESD) according to IEC 1000-4-2 (severity level 3) test peak voltage : ● at discharge thru air 8 kV ● at discharge thru relay's contact 6 kV time between two discharges > 1s number of discharges on each selected point 10 – radiated electromagnetic field immunity test according to IEC 1000-4-3 field strength 10 V/m (severity level 3) frequency range 27 MHz to 1000 MHz sweep speed 1.5 x 10E-3 decade/s – fast transient burst test (FTT) according to IEC 1000-4-4 interference voltage for : mains terminals 115/230 V 2 kV mains terminals 24 V 2 kV output terminals 24 V 1 kV output terminals 115/230 V 2 kV input terminals 24 V 1 kV input terminals 115/230 V 2 kV analogue input/output terminals 1 kV CS 31 bus 2 kV programming interface 0.5 kV – surge immunity according to IEC 1000-4-5 test voltage for assymetric coupling common mode power supply (115/230 VAC) 2 kV power supply (24 VDC) 1 kV digital inputs/outputs 1 kV test voltage for symetric coupling differential mode power supply (115/230 VAC) 1 kV power supply (24 VDC) 1 kV digital inputs/outputs 1 kV ● ABB Procontic CS 31 system bus The CS 31 bus is a shield twisted pair RS485 – cross 0.22 ... 0.8 mm2 (N° AWG 24 ... N° AWG 18) – twists > 10 per metre – resistance 100 /km – impedance characteristic 100 to 150 – capacitance < 150 nF/km – shield – termination 120 , 1/4 Watt resistor connected at the end of the bus – number of points of connections 31 slaves + 1 master 1 ABB Procontic CS31/Edition : 04.96 - FRCTL 3 - 1 General operation 3 General operation 3.1 CPU communication with remote units Communication between the central units and the remote units requires no user intervention as it is carried out by a dedicated serial interface. The dual port RAM of the central unit enables data transfer between the user program processor and the dedicated serial interface. In the read cycle, data is taken from the remote unit and stored within the dual port RAM via the bus and dedicated serial interface, the user program processor then reads the data from the dual port RAM. Similarly, data is transfered from the dual port RAM to the remote units via the dedicated serial interface and bus for the write cycle. CPU User program processor Dedicated serial interface Dual port RAM Remote unit Remote unit Twisted pair bus (RS 485) C 223 D 3.2 Addressing of the remote units All system bus request telegrams have an address. The remote unit which has the same address as the telegram receives and responds to the data. The address of the remote unit is set using the DIL switches of the plug-in base. The inputs and outputs have the following address structure: yy, xx yy represents the remote unit number, xx represents the channel number. Example Address setting of DIL-switches : 03 Number of channels on remote unit : 08 The I/O channels are simply addressed from 03, 00 to 03, 07 within the user program of the central unit, as though they were centralized. 3.3 System bus This is a simple 2-wire serial connection (RS 485). Connection type Serial RS 485 Mode Half-Duplex Baud rate 187.5 k bauds Maximum length 500 metres Isolation opto-couplers Material twisted pair NOTE : For the wiring precautions and characteristics see the "hardware" chapter