678-17004-501493
电源24 VDC 230 VAC/120 VAC
每个第十六单元的输入数量16
电源隔离否是（1500 VAC）
输入光隔离是（1500VAC）是（1500VAC）
电源输出调节24 VDC（±5%）--
输入信号电平，标称值24 VDC 24 VDC
输入信号电平：
0信号–3至+5V–3至+5V
1信号+15至+30V+15至+30V
开路检测--
24 VDC 6 mA 6 mA的输入电流
输入延迟（*）2至32 ms 2至32 ms
大功耗0.2 A 10 VA
大功耗4.5 W 8 W
订单号：FPR 331 6101 R1032 R0036/R0034
重量（kg）0.25 0.43
具有16个输入的二进制隔离输入单元
24 VDC的通道。
装置正面说明：
● 十六个黄色输入状态led的«0»至«15»。。。。。。。。。。➀ ● «测试»按钮。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。➁ ● 红色错误指示灯。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。➂ ● 错误代码列表。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。➃
该装置必须安装在插件基座ECZ上
每个单元16个输入
94 C 128 D
（*）此时间可以更改，出厂设置为8毫秒。
注：设置输入延迟后，有效
该值比所选值高5毫秒。
ICSI 16 E1 230 VAC 10 VA
输入/输出远程装置ABB Procontic CS 31
单元错误
总线错误测试
0
1.
2.
3.
4.
5.
6.
7输入
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
➀
➃ ➁ ➂
ICSI 16 E1 4.1.5-2 ABB Procontic CS31/版本：11.94-FRCTL 2
● 电气连接
电源24 VDC
C 133D/GB
电源230 VAC和120 VAC
注：如果仅使用一个外部电源
24 VDC对于输入，不同的公用电必须
连接在一起并连接到
电源。
● 初始化
配置并连接装置后：
–装置在通电后自动初始化。
–初始化后，错误指示灯熄灭。
–16个输入的状态显示在16个led上。
C 134D/GB
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
12345678
在上
24 VDC
120伏交流电
230伏交流电
盾
普通（E-H）
普通（A-D）
A F GH BCD E
+
–
24
直流电压
+
–
24
直流电压
我也不是JKLM
通用（M-R）
普通（I-L）
+
24
–
直流电压
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
12345678
在上
24 VDC
120伏交流电
230伏交流电
盾
普通（E-H）
普通（A-D）
A F GH BCD E
+
–
24
直流电压
我也不是JKLM
通用（M-R）
普通（I-L）
+
24
–
直流电压
电源
230伏交流电
120伏交流电
L1 N PE
2 ABB Procontic CS31/版本：11.94-FRCTL 4.1.5-3 ICSI 16 E1
● 利用
中央单元中使用的变量
中央单元07 KR 31，07 KR 91 UCZA/UCZB PCZB
07节92、07节93
00…61 00…62 1…31上的地址xx
插件基座ECZ
打开8号开关
插件基座ECZ OFF ON OFF
输入一个Exx，00 Exx，00 Exx，08 Ixx00
B Exx，01 Exx，01 Exx，09 Ixx01
C Exx，02 Exx，02 Exx，10 Ixx02
D Exx，03 Exx，03 Exx，11 Ixx03
E Exx，04 Exx，04 Exx，12 Ixx04
F Exx，05 Exx，05 Exx，13 Ixx05
G Exx，06 Exx，06 Exx，14 Ixx06
H Exx，07 Exx，07 Exx，15 Ixx07
I Exx，08 Exx+1，00 Exx+1，08 Ixx08
J Exx，09 Exx+1，01 Exx+1，09 Ixx09
K Exx，10 Exx+1，02 Exx+1，10 Ixx10
L Exx，11 Exx+1，03 Exx+1，11 Ixx11
M Exx，12 Exx+1，04 Exx+1，12 Ixx12
N Exx，13 Exx+1，05 Exx+1，13 Ixx13
O Exx，14 Exx+1，06 Exx+1，14 Ixx14
P Exx，15 Exx+1，07 Exx+1，15 Ixx15
关于PC板07 CM 90和连接器板07 CS 61和35 CS 91，请参阅其各自的说明
每个输入的可用配置：
–延迟
● 故障指示
led指示如下：
Led 0：“单元错误”
Led 1：“总线错误”
输入通道的状态显示为：
Led 7：“输入”
如果发生错误，红色led错误指示灯亮起（参见第9章，
第2卷«故障情况»）。
2 ABB Procontic CS31/版本：11.95-FRCTL 4.2.1-1 ICSO 08 R1
4.2.1 ICSO 08 R1二进制输出远程装置
8继电器输出2A
技术特点
电源24 VDC 230 VAC/120 VAC
每个第八单元的输出数量8
电源隔离否是（1500 VAC）
输出隔离是（1500 VAC）是（1500 VAC）
开关容量
120/230 AC 2 A 2 A
直流60 W（2A）60 W（2A）
负载电流，标称值2 A AC-1 2 A AC-1
1 A AC-3 1 A AC-3
小值12 VDC 12 VDC
10毫安10毫安
8个输出16 A 16 A的总电流
短路停机否
电感关断电压变阻器的极限
大功耗0.2 A 6VA
大功耗5 W 5 W
订单号：FPR 331 2101 R1012 R0016/R0014
重量（kg）0.25 0.43
具有8个继电器输出的二进制输出单元
通道2 A。
装置正面说明：
● 八个黄色输出状态led的«0»到«7»。。。。。。。。。。。。。。➀ ● «测试»按钮。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。➁ ● 红色错误指示灯。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。➂ ● 错误代码列表。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。➃
该装置必须安装在插件基座ECZ上
每个单元8个输出
C 126 D
ICSO 08 R1 230 VAC 10 VA
输入/输出远程装置ABB Procontic CS 31
单元错误
总线错误测试
0
1.
2.
3.
4.
5.
6.
7.
输出
0 1 2 3 4 5 6 7
➀
➃ ➁ ➂
ICSO 08 R1 4.2.1-2 ABB Procontic CS31/版本：11.95-FRCTL PDC60-300-504140
 678-17004-501493
Power supply 24 VDC 230 VAC/120 VAC Number of inputs per unit 16 16 Power supply isolation no yes (1500 VAC) Inputs opto-isolated yes(1500VAC) yes(1500VAC) Supply output regulated 24 VDC (± 5 %) - - Signal level of the input, nominal value 24 VDC 24 VDC Signal level of the input : 0 signal –3 to +5V –3 to +5V 1 signal +15 to +30V +15 to +30V Open circuit detection - - Input current for 24 VDC 6 mA 6 mA Input delay (*) 2 to 32 ms 2 to 32 ms Maximum power consumption 0.2 A 10 VA Maximum power dissipation 4.5 W 8 W Order number : FPR 331 6101 R1032 R0036/R0034 Weight (kg) 0.25 0.43 Binary isolated input unit with16 input channels for 24 VDC. Description of the unit front : ● Sixteen yellow input status led's «0» to «15» ..........➀ ● «TEST» push-button ............................................... ➁ ● Red error led ........................................................... ➂ ● List of error codes.................................................... ➃ The unit has to be mounted on a plug-in base ECZ 16 inputs per unit 94 C 128 D (*) This time can be changed, factory setting 8 ms. Note : After setting the input delay,the effective value is 5 ms higher than the selected value. ICSI 16 E1 230 VAC 10 VA I/O REMOTE UNIT ABB Procontic CS 31 Unit error Bus error TEST 0 1 2 3 4 5 6 7 Input 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 ➀ ➃ ➁ ➂ ICSI 16 E1 4.1.5-2 ABB Procontic CS31/Edition : 11.94 - FRCTL 2 ● Electrical connection Power supply 24 VDC C 133D/GB Power supply 230 VAC and 120 VAC Note : In case of use of only one external power supply 24 VDC for inputs, the different communs have to be connected together and to the O VDC of the power supply. ● Initialization After configured and wired the unit : – the unit initializes itself after power On. – the error led goes out after initialization. – the status of 16 inputs is displayed on the 16 led's. C 134D/GB 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 12345678 ON 24 VDC 120 VAC 230 VAC Shield Common (E-H) Common (A-D) A F GH BCD E + – 24 VDC + – 24 VDC I NOR JKLM Common (M-R) Common (I-L) + 24 – VDC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 12345678 ON 24 VDC 120 VAC 230 VAC Shield Common (E-H) Common (A-D) A F GH BCD E + – 24 VDC I NOR JKLM Common (M-R) Common (I-L) + 24 – VDC Power supply 230 VAC 120 VAC L1 N PE 2 ABB Procontic CS31/Edition : 11.94 - FRCTL 4.1.5-3 ICSI 16 E1 ● Utilization VARIABLES USED IN THE CENTRAL UNIT CENTRAL UNITS 07 KR 31, 07 KR 91 UCZA/UCZB PCZB 07 KT 92, 07 KT 93 Address xx on the 00 … 61 00 … 62 1 … 31 plug-in base ECZ Switch N° 8 on the plug-in base ECZ OFF OFF ON OFF Input A Exx, 00 Exx, 00 Exx, 08 Ixx00 B Exx, 01 Exx, 01 Exx, 09 Ixx01 C Exx, 02 Exx, 02 Exx, 10 Ixx02 D Exx, 03 Exx, 03 Exx, 11 Ixx03 E Exx, 04 Exx, 04 Exx, 12 Ixx04 F Exx, 05 Exx, 05 Exx, 13 Ixx05 G Exx, 06 Exx, 06 Exx, 14 Ixx06 H Exx, 07 Exx, 07 Exx, 15 Ixx07 I Exx, 08 Exx+1, 00 Exx+1, 08 Ixx08 J Exx, 09 Exx+1, 01 Exx+1, 09 Ixx09 K Exx, 10 Exx+1, 02 Exx+1, 10 Ixx10 L Exx, 11 Exx+1, 03 Exx+1, 11 Ixx11 M Exx, 12 Exx+1, 04 Exx+1, 12 Ixx12 N Exx, 13 Exx+1, 05 Exx+1, 13 Ixx13 O Exx, 14 Exx+1, 06 Exx+1, 14 Ixx14 P Exx, 15 Exx+1, 07 Exx+1, 15 Ixx15 For the PC board 07 CM 90 and the coupler boards 07 CS 61 and 35 CS 91, refer to their own description The available configuration for each input : – delay ● Fault indication The led's indicate the following : Led 0 : "Unit error" Led 1 : "Bus error" The status of an input channel is shown by : Led 7 : "Input" If an error occurs the red led error is On (see Chapter 9, Volume 2 «In case of failure»). 2 ABB Procontic CS31/Edition : 11.95 - FRCTL 4.2.1-1 ICSO 08 R1 4.2.1 ICSO 08 R1 Binary Output remote unit 8 relay outputs 2A TECHNICAL CHARACTERISTICS Power supply 24 VDC 230 VAC/120 VAC Number of outputs per unit 8 8 Power supply isolation no yes (1500 VAC) Outputs isolated yes (1500 VAC) yes (1500 VAC) Switching capacity 120/230 AC 2 A 2 A DC 60 W (2A) 60 W (2A) Load current,nominal value 2 A AC-1 2 A AC-1 1 A AC-3 1 A AC-3 Minimum values 12 VDC 12 VDC 10 mA 10 mA Total current for 8 outputs 16 A 16 A Short circuit shutdown no no Limit of the inductive shutdown voltage Varistor Varistor Maximum power consumption 0.2 A 6VA Maximum power dissipation 5 W 5 W Order number : FPR 331 2101 R1012 R0016/R0014 Weight (kg) 0.25 0.43 Binary output unit with 8 relay output channels 2 A. Description of the unit front : ● Eight yellow output status led's «0» to «7»..............➀ ● «TEST» push-button ............................................... ➁ ● Red error led ........................................................... ➂ ● List of error codes.................................................... ➃ The unit has to be mounted on a plug-in base ECZ 8 outputs per unit C 126 D ICSO 08 R1 230 VAC 10 VA I/O REMOTE UNIT ABB Procontic CS 31 Unit error Bus error TEST 0 1 2 3 4 5 6 7 IOutput 0 1 2 3 4 5 6 7 ➀ ➃ ➁ ➂ ICSO 08 R1 4.2.1-2 ABB Procontic CS31/Edition : 11.95 - FRCTL 2 ● Electrical connection Power supply 24 VDC 94 C 137D 94 C 138D 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 12345678 ON 24 VDC 120 VAC 230 VAC Shield A F FGG H H ABBC CD DE E = / ~ = / ~ = / ~ = / ~ = / ~ = / ~ = / ~ = / ~ + – 24 VDC Load Load Load Load Load Load Load Load 19 20 + – 24 U Note : In case of inductive load with a DC current, a free wheele diode Has to be mounted in parallel of the load according the following example for the output A : ● Initialization After configured and wired the unit : – the unit initializes itself after power On. – the error led goes out after initialization. – the status of 8 outputs is displayed on the 8 led's. Power supply 230 VAC and 120 VAC 94 C 139D 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 12345678 ON 24 VDC 120 VAC 230 VAC Shield A F FGG H H ABBC CD DE E Power supply 230 VAC 120 VAC L1 N PE = / ~ = / ~ = / ~ = / ~ = / ~ = / ~ = / ~ = / ~ Load Load Load Load Load Load Load Load 2 ABB Procontic CS31/Edition : 11.95 - FRCTL 4.2.1-3 ICSO 08 R1 ● Utilization VARIABLES USED IN THE CENTRAL UNIT CENTRAL UNITS 07 KR 31, 07 KR 91 UCZA/UCZB PCZB 07 KT 92, 07 KT 93 Address xx on the 00 … 62 00 … 63 1 … 31 plug-in base ECZ Switch N° 8 on the plug-in base ECZ OFF ON OFF ON OFF Output A Axx, 00 Axx,08 Axx, 00 Axx, 08 Oxx00 B Axx, 01 Axx,09 Axx, 01 Axx, 09 Oxx01 C Axx, 02 Axx,10 Axx, 02 Axx, 10 Oxx02 D Axx, 03 Axx,11 Axx, 03 Axx, 11 Oxx03 E Axx, 04 Axx,12 Axx, 04 Axx, 12 Oxx04 F Axx, 05 Axx,13 Axx, 05 Axx, 13 Oxx05 G Axx, 06 Axx,14 Axx, 06 Axx, 14 Oxx06 H Axx, 07 Axx,15 Axx, 07 Axx, 15 Oxx07 For the PC board 07 CM 90 and the coupler boards 07 CS 61 and 35 CS 91, refer to their own description ● Fault indication The led's indicate the following : Led 0 : "Unit error" Led 1 : "Bus error" The status of an output channel is shown by : Led 6 : "Output" If an error occurs the red led error is On (see Chapter 9, Volume 2 «In case of failure»). 2 ABB Procontic CS31/Edition : 04.96 - FRCTL 4.2.2-1 ICSO 08 Y1 4.2.2 ICSO 08 Y1 Binary Output remote unit 8 outputs 24 VDC 2A TECHNICAL CHARACTERISTICS Power supply 24 VDC 230 VAC/120 VAC Number of outputs per unit 8 8 Power supply isolation no yes (1500 VAC) Outputs opto-isolated yes(1500VAC) yes(1500 VAC) Maximum current 2 A AC1 2 A AC1 Leackage current 4 mA 4 mA Total current for the 8 outputs 8 A 8 A Short circuit protection for each output yes yes Overload thermal protection for each output yes yes Maximum power consumption 0.2 A 6VA Maximum power dissipation 6 W 8 W Order number : FPR 331 1101 R1022 R0026/R0024 Weight (kg) 0.25 0.43 Binary output unit with 8 transitor output channels 24 VDC 2 A. Description of the unit front : ● Eight yellow output status led's «0» to «7»..............➀ ● «TEST» push-button ............................................... ➁ ● Red error led ........................................................... ➂ ● List of error codes.................................................... ➃ The unit has to be mounted on a plug-in base ECZ 8 outputs per unit ICSO 08 Y1 230 VAC 10 VA I/O REMOTE UNIT ABB Procontic CS 31 Unit error Bus error Power off Overload Short-circuit TEST 0 1 2 3 4 5 6 7 Output 0 1 2 3 4 5 6 7 ➀ ➃ ➁ ➂ C 130 D ICSO 08 Y1 4.2.2-2 ABB Procontic CS31/Edition : 04.96 - FRCTL 2 ● Electrical connection Power supply 24 VDC Power supply 230 VAC and 120 VAC ● Initialization After configured and wired the unit : – the unit initializes itself after power On. – the error led goes out after initialization. – the status of 8 outputs is displayed on the 8 led's. 94 C 142 D 94 C 143 D 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 12345678 ON 24 VDC 120 VAC 230 VAC Shield A F GH BCDE Power supply 230 VAC 120 VAC L1 N PE A FGH BCDE Common + Common + Common – – 24 + VDC Load Load Load Load Load Load Load Load 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 12345678 ON 24 VDC 120 VAC 230 VAC Shield A F GH BCDE + – 24 VDC A FGH BCDE Common + Common + Common – – 24 + VDC Load Load Load Load Load Load Load Load 2 ABB Procontic CS31/Edition : 04.96 - FRCTL 4.2.2-3 ICSO 08 Y1 ● Utilization VARIABLES USED IN THE CENTRAL UNIT CENTRAL UNITS 07 KR 31, 07 KR 91 UCZA/UCZB PCZB 07 KT 92, 07 KT 93 Address xx on the 00 … 62 00 … 63 1 … 31 plug-in base ECZ Switch N° 8 on the plug-in base ECZ OFF ON OFF ON OFF Output A Axx, 00 Axx,08 Axx, 00 Axx, 08 Oxx00 B Axx, 01 Axx,09 Axx, 01 Axx, 09 Oxx01 C Axx, 02 Axx,10 Axx, 02 Axx, 10 Oxx02 D Axx, 03 Axx,11 Axx, 03 Axx, 11 Oxx03 E Axx, 04 Axx,12 Axx, 04 Axx, 12 Oxx04 F Axx, 05 Axx,13 Axx, 05 Axx, 13 Oxx05 G Axx, 06 Axx,14 Axx, 06 Axx, 14 Oxx06 H Axx, 07 Axx,15 Axx, 07 Axx, 15 Oxx07 For the PC board 07 CM 90 and the coupler boards 07 CS 61 and 35 CS 91, refer to their own description ● Fault indication The led's indicate the following : Led 0 : "Unit error" Led 1 : "Bus error" Led 3 : "Power off" Led 4 : "Overload" Led 5 : "Short-circuit" The status of an output channel is shown by : Led 6 : "Output" If an error occurs the red led error is On (see Chapter 9, Volume 2 «In case of failure»). 2 ABB Procontic CS31/Edition : 02.95 - FRCTL 4.2.3-1 ICSO 16 N1 4.2.3 ICSO 16 N1 Binary Output remote unit 16 outputs 24 VDC 0.5A TECHNICAL CHARACTERISTICS Power supply 24 VDC 230 VAC/120 VAC Number of outputs per unit 16 16 Power supply isolation no yes (1500 VAC) Outputs opto-isolated no no Maximum current 0.5 A 0.5 A Total current for the 16 outputs 8 A 8 A Short circuit protection for each output yes yes Overload thermal protection for each output yes yes 2 A with 25 °C ambient 1.5 A with 55 °C ambient Maximum power consumption 0.2 A 10 VA Maximum power dissipation 6 W 8 W Order number : FPR 331 3101 R1052 R0056/R0054 Weight (kg) 0.25 0.43 Binary output unit with 16 transitor output channels 24 VDC 0.5A. Description of the unit front : ● Sixteen yellow output status led's «0» to «15» ........➀ ● «TEST» push-button ............................................... ➁ ● Red error led ........................................................... ➂ ● List of error codes.................................................... ➃ The unit has to be mounted on a plug-in base ECZ 16 outputs per unit ICSO 16 N1 230 VAC 10 VA I/O REMOTE UNIT ABB Procontic CS 31 Unit error Bus error Short circuit / overload TEST 0 1 2 3 4 5 6 7 Output 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 ➀ ➃ ➁ ➂ C 206 D ICSO 16 N1 4.2.3-2 ABB Procontic CS31/Edition : 02.95 - FRCTL 2 ● Electrical connection Power supply 24 VDC Power supply 230 VAC and 120 VAC C 208 D 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 12345678 ON 24 VDC 120 VAC 230 VAC Shield A F GH BCDE + – 24 VDC I NOP JKLM Common + Common + Common – – 24 + VDC Load Load Load Load Load Load Load Load Load Load Load Load Load Load Load Load C 207 D Electric schema for a transistor output Note : The both commun + terminals have to be connected to garanty a right diagnosis function. If the common + terminals are not connected to an external power supply 24 VDC, the corresponding outputs are reset to 0. – A free wheel diode is not necessary because the protection is integrated into the transistor component. – An external thermal fuse max. 10 A has to be connected between the common + terminals and the 24 VDC to avoid damage in case of use of a lot of overload outputs. ● Initialization After configured and wired the unit : – the unit initializes itself after power On. – the error led goes out after initialization. – the status of 16 outputs is displayed on the 16 led's. Common + Common – Output Status 33V 33V 0V DC Logic Charge Pump R L Load C 209 D 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 12345678 ON 24 VDC 120 VAC 230 VAC Shield A F GH BCDE Power supply 230 VAC 120 VAC L1 N PE I N O P JKLM Common + Common + Common – – 24 + VDC Load Load Load Load Load Load Load Load Load Load Load Load Load Load Load Load 2 ABB Procontic CS31/Edition : 02.95 - FRCTL 4.2.3-3 ICSO 16 N1 ● Utilization VARIABLES USED IN THE CENTRAL UNIT CENTRAL UNITS 07 KR 31, 07 KR 91 UCZA/UCZB PCZB 07 KT 92, 07 KT 93 Address xx on the 00 … 61 00 … 63 1 … 31 plug-in base ECZ Switch N° 8 on the plug-in base ECZ OFF OFF ON OFF Output A Axx, 00 Axx, 00 Axx, 08 Oxx00 B Axx, 01 Axx, 01 Axx, 09 Oxx01 C Axx, 02 Axx, 02 Axx, 10 Oxx02 D Axx, 03 Axx, 03 Axx, 11 Oxx03 E Axx, 04 Axx, 04 Axx, 12 Oxx04 F Axx, 05 Axx, 05 Axx, 13 Oxx05 G Axx, 06 Axx, 06 Axx, 14 Oxx06 H Axx, 07 Axx, 07 Axx, 15 Oxx07 I Axx, 08 Axx + 1, 00 Axx + 1, 08 Oxx08 J Axx, 09 Axx + 1, 01 Axx + 1, 09 Oxx09 K Axx, 10 Axx + 1, 02 Axx + 1, 10 Oxx10 L Axx, 11 Axx + 1, 03 Axx + 1, 11 Oxx11 M Axx, 12 Axx + 1, 04 Axx + 1, 12 Oxx12 N Axx, 13 Axx + 1, 05 Axx + 1, 13 Oxx13 O Axx, 14 Axx + 1, 06 Axx + 1, 14 Oxx14 P Axx, 15 Axx + 1, 07 Axx + 1, 15 Oxx15 For the PC board 07 CM 90 and the coupler boards 07 CS 61 and 35 CS 91, refer to their own description ● Fault indication The led's indicate the following : Led 0 : "Unit error" Led 1 : "Bus error" Led 3 : "Power off" Led 5 : "Short-circuit or Overload" The status of an output channel is shown by : Led 6 : "Output" If an error occurs the red led error is On (see Chapter 9, Volume 2 «In case of failure») | | |
已过期
3515
收藏商品
QQ咨询
当前商品暂无此评价～
2778087246
18150367963
记住账号
