6LV-DFVBW8-504117
寻址
必须在每个模块上设置地址，以便中央单元能够正确访问输入和输出。
关于项目“寻址”的详细说明包含在
中央单元和耦合器。
模块地址设置在模块右侧滑块下方的DIL开关上。
如果中央单元07 KR 91、07 KT 92和07 KT 93为
用作总线主控，以下操作模式
（地址分配）有效，取决于位置
地址DIL开关1：
端子/输入端子/输出
5 E n，00 28 A n，00
6 E n，01 29 A n，01
7 E n，02 30 A n，02
8 E n，03 31 A n，03
9 E n，04 32 A n，04
10 E n，05 33 A n，05
11 E n，06 34 A n，06
12 E n，07 35 A n，07
13 E n，08 36 A n，08
14 E n，09 37 A n，09
15 E n，10 38 A n，10
16 E n，11 39 A n，11
17 E n，12 40 A n，12
18 E n，13 41 A n，13
19 E n，14 42 A n，14
20 E n，15 43 A n，15
n： 模块地址，设置在地址上
DIL开关2号。。。7.
推荐的模块地址
07 KR 91/07 KT 92/93作为总线主控器：
08, 10, 12......60（偶数地址）
中央单元07 KR 91/07 KT 92/07 KT 93
8号地址DIL开关见单独说明（本页右上角）。
地址DIL开关1设置为ON意味着，
16个输入和16个输出的分配是不变的。所有组合输入/输出仅为输出（见下文）。
在该设置下，模块仅使用CS31系统总线上的一个地址。
16个输入和16个输出可用。
图4.3.4-3：信道地址，如果
1号DIL开关设置为ON
设置8号地址DIL开关
地址DIL开关用于定义输出是否应在过载或短路后再次打开
自动或通过确认。的含义
开关位置：
关闭（出厂设置）：消除错误后，
输出再次自动打开。
ON：消除错误后，输出
按下测试按钮或通过PLC程序（连接元件）确认再次打开
CS31QU）或通过中央单元上的串行接口。
期限/输入项/输出-输入
5 E n，00 28 A n，00
6 E n，01 29 A n，01
7 E n，02 30 A n，02
8 E n，03 31 A n，03
9 E n，04 32 A n，04
10 E n，05 33 A n，05
11 E n，06 34 A n，06
12 E n，07 35 A n，07
13 E n，08 36 A n，08 E n+1,00
14 E n，09 37 A n，09 E n+1,01
15 E n，10 38 A n，10 E n+1,02
16 E n，11 39 A n，11 E n+1,03
17 E n，12 40 A n，12 E n+1,04
18 E n，13 41 A n，13 E n+1,05
19 E n，14 42 A n，14 E n+1,06
20 E n，15 43 A n，15 E n+1,07
中央单元07 KR 91/07 KT 92/07 KT 93
地址DIL开关1设置为OFF（出厂设置）意味着16个输入和8个输出
是不变的分配。8个组合
输入/输出可以单独处理为
输入或输出（见下文）。
通过此设置，模块使用两个地址
在CS31系统总线上。24二进制输入和16
二进制输出通道被占用。模块
有16个输入、8个输出和8个组合输入/
立即输出。An+1,00。。。15和En1,08。。。15是
未使用。如果需要，这些地址可以
用于其他模块。
图4.3.4-4：信道地址，如果
1号DIL开关设置为OFF
n： 模块地址，设置在地址上
DIL开关2号。。。7.
推荐的模块地址
07 KR 91/07 KT 92/93作为总线主控器：
08, 10, 12......60（偶数地址）
8号地址DIL开关见单独说明（本页右上角）。
ICDG 32 L1 4.3.4–4 ABB Procontic CS31/发布日期：07.94
备注：
模块ICDG 32 L1读取DIL的位置
通电后初始化期间仅切换一次。如果
开关位置在模块运行期间发生变化，这些变化在
下一次初始化。例外：DIL开关的位置
8（定义是否应打开输出
再次过载或短路后自动或通过
确认）当前已更新。
输入/输出配置
模块ICDG 32 L1不存储任何配置
数据定义了8个组合输入/输出通道
作为用户程序的输入或输出。
这意味着，每个组合输入/输出
可以用作输入或输出（或可读输出）
通过分别从其读取数据或向其发送数据。如果
用作输入时，不得向相应输出发送信号“1”。有关DIL开关和地址分配的设置，请参见图4.3.4-3和4.3.4-4（一页
同上）。
正常操作
模块在通电后自行初始化。在期间
初始化所有LED亮起。
如果CS31系统总线未运行，则LED 3
闪烁。
当总线运行时，LED 3再次熄灭
运行正常，模块未检测到错误。
16个绿色和16个黄色LED 1显示
32个通道的信号状态。
诊断和显示
诊断功能：
–输出短路/过载（I>0.7 A）
–至的短路/过载信息
中央单元
–存储此信息后，将其保存以备
读数（错误类别  6LV-DFVBW8-504117
Electrical isolation versus the CS31 system bus interface Input signal delay typ. 7 ms Signalling of input statuses one green LED per channel, the LEDs correspond functionally to the input signals Input signal voltage signal 0 –30 V...+ 5 V signal 1 +13 V...+30 V ripplewhen signal 0 within –30 V...+ 5 V when signal 1 within +13 V...+30 V Allowed input overvoltage + 36 V, for 100 ms only Input current per channel input voltage = +24 V typ. 7.0 mA input voltage = + 5 V > 1.0 mA input voltage = +13 V > 2.0 mA input voltage = +30 V < 10.0 mA Labelling for the inputs Symbol names or short signal designations can be labelled on the front panel foil. The foil is not removeable. Conductor cross section of the removable terminal blocks max. 1.5 mm2, terminal-to-terminal distance 3.81 mm Technical data for the binary outputs Number of channels per module 8 transistor outputs Distribution of channels into groups 1 groups of 8 channels, channels An,00...An,07 Reference potential for all outputs terminals 24/25 (minus pole of the supply voltage, signal name M) Common voltage supply for all outputs terminals 22/23 (plus pole of the supply voltage, signal name L+) Electrical isolation versus the CS31 system bus interface Signalling of output statuses one yellow LED per channel, the LEDs correspond functionally to the output signals Output current rated value 250 mA with L+ = 24 V maximum value 312 mA with L+ = 24 V + 25 % leakage current with signal 0 < 0.5 mA Demagnetization of inductive loads internally with free-wheeling diode and Z-diode (Z-diode voltage is 12 V) Switching frequency with inductive loads max. 0.5 Hz Switching frequency with lamp load max. 11 Hz with max. 5 W Short-circuit-proof/overload-proof yes Overload message (I > 0,7 A) yes, after ca. 100 ms Limitation of output current yes Output is switched on again after acknowledgement, if DIL switch No. 8 = ON automatically, if DIL switch No. 8 = OFF Total load (together with the output currents of the combined inputs/outputs) max. 4 A Labelling for the outputsSymbol names or short signal designations can be labelled on the front panel foil. The foil is not removeable. ABB Procontic CS31/Issued: 04.94 4.3.4–7 ICDG 32 L1 Conductor cross section of the removable terminal blocks max. 1.5 mm2, terminal-to-terminal distance 3.81 mm Technical data of the configurable inputs/outputs The 8 combined input/output channels are defined individually as inputs or outputs by the user program. This is done by reading from or writing to the corresponding channel. Number of channels per module 8 inputs/transistor outputs Distribution of channels into groups 1 group of 8 channels if the channels used as inputs channels En+1,00...En+1,07 if the channels used as outputs channels An,08...An,15 Signalling of input/output statuses one yellow LED per channel, the LEDs correspond functionally to the binary signals Other technical data see binary inputs, see binary outputs Connection to the ABB Procontic CS31 system bus Interface standard EIA RS–485 Electrical isolation versus supply voltage, inputs/outputs Conductor cross section of the removable terminal block max. 2.5 mm2, terminal-to-terminal distance 5.08 mm Mechanical data Mounting on DIN rail according to DIN EN 50022–35, 15 mm deep. The DIN rail is located in the middle between the upper and the lower edges of the module. Fastening by screws using 4 M4 screws. Width x height x depth 120 x 140 x 85 mm Wiring method by removable terminal blocks with screw-type terminals, conductor cross section max. 2.5 mm2, terminal-to-terminal distance 5.08 mm max. 1.5 mm2, terminal-to-terminal distance 3.81 mm Weight 450 g Outline dimensions (for mounting) see the drawing on the next page Mounting hints Mounting position vertical, terminals above and below Cooling The natural convection cooling must not hindered by cable ducts or other material mounted in the switch cabinet. Ordering data Module ICDG 32 L1 R0101 Order No. GJR5 2514 00 R0101 Scope of delivery Binary input/output module ICDG 32 L1 1 5–pole terminal blocks (5.08 mm) 1 3–pole terminal block (5.08 mm) 4 9–pole terminal blocks (3.81 mm) ICDG 32 L1 4.3.4–8 ABB Procontic CS31/Issued: 07.94 ABB Procontic CS31 ICDG 32 L1 Fig. 4.3.4–5: ICDG 32 L1, outline dimensions, the dimensions for assembly bore holes are printed in bold. 65 130 65 140 94 120 85 111 102 5 All dimensions in mm. 94 The module is 85 mm deep. If a DIN rail is used, the mounting depth is increased by the overall depth of the rail. 20 2 ABB Procontic CS31/Edition : 11.96 - FRCTL 4.3.5-1 ICSK 20 N1 4.3.5 ICSK 20 N1 Binary Input/Output remote unit 12 inputs 24 VDC / 8 transitor outputs Binary input/output unit with12 input channels for 24 VDC and 8 transistor output 24VDC 0.5A channels. Description of the unit front : ● Twelwe yellow input status led's «0» to «11» ..........➀ ● Eight yellow output status led's «0» to «7»..............➁ ● One green led labelled "Supply" to indicate the presence of the supply ............................................ ➂ ● «TEST» push-button ............................................... ➃ ● Red error led ........................................................... ➄ ● List of error codes.................................................... ➅ The unit has to be mounted on a plug-in base ECZ C 203 D 12 inputs/8 transistor outputs per unit GENERAL CHARACTERISTICS Power supply 24 VDC 230 VAC/120 VAC Number of inputs per unit 12 12 Number of outputs per unit 8 8 Isolated power supply no yes (1500 VAC) Maximum consumption 0.3 A 10 VA Order number FPR 3331001 R 1202 R 0206/R 0204 Weight (kg) 0.25 0.43 INPUT CHARACTERISTICS Signal level of the input, nominal value 24 VDC 24 VDC Opto isolated inputs no no Signal level of the inputs, nominal value 24 VDC 24 VDC Signal level of the input 0 signal –3 to +5V –3 to +5V 1 signal +15 to +30V +15 to +30V Input current for 24 VDC 5 mA 5 mA Input delay (*) 5 ms 5 ms (*) This delay can't be modified ICSK 20 N1 230 VAC 10 VA I/O REMOTE UNIT ABB Procontic CS 31 Unit error Bus error Short circuit / overload TEST 0 1 2 3 4 5 6 7 ➀ ➅ ➄ ➃ 0 1 2 3 4 5 6 7 IN OUT SUPPLY ➂ ➁ ICSK 20 N1 4.3.5-2 ABB Procontic CS31/Edition : 11.96 - FRCTL 2 OUTPUT CHARACTERISTICS Isolated no no Switching capacity under 0.5 A (resistive or inductive load) DC 15W (0.5A) 15 W (0.5A) Nominal current 0.5 A 0.5 A Supply output 24 VDC 100 mA no yes Total curent for 8 outputs 4A 4A Short-circuit protection for each output yes yes Thermal protection for each output yes yes 2 A with 25 °C ambient 1.5 A with 55 °C ambient Over voltage protection yes yes 2 ABB Procontic CS31/Edition : 02.95 - FRCTL 4.3.5-3 ICSK 20 N1 ● Electrical connection Power supply 24 VDC Power supply 230 VAC and 120 VAC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 12345678 ON 24 VDC 120 VAC 230 VAC Sheild A F GH I J K L Earth Common + Common – B C D E M RS T NOPQ Common M.T + Common M.T – – + 24 VDC + – 24 VDC Load Load Load Load Load Load Load Load C 204 D C 205 D Note : The internal 24 VDC (100 mA) power supply is only available for the 230 VAC/120 VAC versions. This power is used to power the inputs. In case of the 24 VDC version, the 0 V of the second external power supply for the inputs has to be connected to the common "–". The 0 V of the 24 VDC power supply for the outputs has to be connected to the common M-T -. If the 24 VDC of the external supply is not connected to the common M-P +, the outputs are reset to 0. – A free wheel diode is not necessary because the protection is integrated into the transistor component. – An external thermal fuse max. 5 A has to be connected between the common + terminals and the 24 VDC to avoid damage in case of use of a lot of overload outputs. ● Initialization After configured and wired the unit : – the unit initializes itself after power On. – the error led goes out after initialization. – the status of inputs/outputs is displayed on the 20 led's. | | |
已过期
3532
收藏商品
QQ咨询
当前商品暂无此评价～
2778087246
18150367963
记住账号
