易卖工控网(www.ymgk.com)提供”02-321145C03-504013模块备件”,产品详情:品牌/厂家:0040-32460-504815、型号:02-321145C03-504013、成色:全新、货期:现货 1天内发货、保修:180天,更多产品详情就上易卖工控网。
02-321145C03-504013 B终端电缆 C FBM201 RH914SQ D现场总线电缆 E FBM基板 F电力电缆 PSS 41H-2S201,版本A 5 FBM201/b/c/d模拟输入(0至20 mA,0至100 mV,0至5 V,0 至10 V dc)功能规格 功能规范 过程输入/输出 通信 通过冗余2 Mbps模块与其相关FCM或FCP通信 现场总线 输入通道8个隔离和独立通道 输入范围(每个 通道) FBM201:0至20 mA dc FBM201b:0至100 mV dc FBM201c:0至5 V dc FBM201d:0至10 V dc 输入通道(8)•模拟精度(包括线性度): 量程的±0.03% 精度温度系数:±50 ppm/ºC •现场设备布线距离: 现场设备与FBM的大距离是顺应性的函数 现场设备的电压(22.8 V dc)、导线电阻和压降。 •输入通道阻抗: FBM201:61.5Ω标称值 FBM201b:10 MΩ FBM201c:10 MΩ FBM201d:10 MΩ •输入信号A/D转换: 每个通道使用独立的Sigma-Delta执行A/D信号转换 转换器。 •整合期: 软件可配置 •共模抑制: >50或60 Hz时为100 db •正常模式抑制: >50或60 Hz时为95 db •回路电源保护 每个通道都是通道间电流隔离、电流限制和 电压调节。所有模拟输入受其设计限制,小于30 mA。 如果电流限制电路短路,电流限制在100 mA左右。 •输入通道隔离 每个通道与所有其他通道和地(地)电隔离。 模块/TA能够承受一次施加的600 V交流电势,且不会损坏 任何通道和地面之间,或给定通道和任何 其他通道。 危险 触电、爆炸或电弧闪光危险 这并不意味着这些通道旨在久连接到 这些电平的电压。超出其他地方规定的输入电压限值 在本规范中,违反电气安全规范,并可能使用户暴露在电气环境中 震惊 不遵守这些说明将导致死亡或重伤。 6 PSS 41H-2S201,版本A 功能规范 FBM201/b/c/d模拟输入(0至20 mA,0至100 mV,0至5 V,0 至10 V dc) 功率要求•输入电压范围(冗余): 24 V dc+5%,-10% •消费: 7瓦 •散热: 3 W(大) 标定 要求 无需校准模块和终端组件。 法规遵从性: 电磁 兼容性(EMC) •欧洲EMC指令2004/108/EC(2016年4月20日之前)和2014/30/EU (自2016年4月20日起): 满足:EN61326-1:2013 A级排放和工业抗扰度水平 法规遵从性: 产品安全•美国和加拿大保险商实验室(UL): UL/UL-C认证适用于UL/UL-C认证的I类A-D组;分开 2.温度代码T4基于外壳的系统,当连接到指定的 Foxboro DCS处理器模块。通信电路也满足 国家电气规范725条中定义的2级要求 (NFPA70号)和《加拿大电气规范》(CSA C22.1)16节。对于 更多信息,请参阅标准和紧凑型200系列子系统用户指南 (B0400FA)。 •欧洲低压指令2006/95/EC(2016年4月20日之前)和2014/35/ 欧盟(2016年4月20日开始)和爆炸性环境(ATEX)指令94/9/ 欧盟委员会(2016年4月20日之前)和2014/34/EU(2016年4月20日开始): DEMKO认证为Ex nA IIC T4,用于认证的2区外壳,当 按照标准和 Compact 200系列子系统用户指南(B0400FA)。 RoHS符合欧洲RoHS指令2011/65/EU,包括修订指令 2015/863和2017/2102。 海事认证ABS型式认证和法国船级社海事认证环境类别 酶代码EC31。 02-321145C03-504013 02-321145C03-504013 B Termination Cable C FBM201 RH914SQ D Fieldbus Cables E FBM Baseplate F Power Cable PSS 41H-2S201, Rev A 5 FBM201/b/c/d Analog Input (0 to 20 mA, 0 to 100 mV, 0 to 5 V, 0 to 10 V dc) Functional Specifications Functional Specifications Process I/O Communications Communicates with its associated FCM or FCP via the redundant 2 Mbps module Fieldbus Input Channels 8 isolated and independent channels Input Range (each channel) FBM201: 0 to 20 mA dc FBM201b: 0 to 100 mV dc FBM201c: 0 to 5 V dc FBM201d: 0 to 10 V dc Input Channels (8) • Analog Accuracy (includes linearity): ±0.03% of span Accuracy temperature coefficient: ±50 ppm/ºC • Field Device Cabling Distance: Maximum distance of the field device from the FBM is a function of compliance voltage (22.8 V dc), wire resistance, and voltage drop at the field device. • Input Channel Impedance: FBM201: 61.5 Ω nominal FBM201b: 10 MΩ FBM201c: 10 MΩ FBM201d: 10 MΩ • Input Signal A/D Conversion: Each channel performs A/D signal conversion using an independent Sigma-Delta converter. • Integration Period: Software configurable • Common Mode Rejection: >100 db at 50 or 60 Hz • Normal Mode Rejection: >95 db at 50 or 60 Hz • Loop Power Supply Protection Each channel is channel-to-channel galvanically isolated, current limited, and voltage regulated. All analog inputs are limited by their design to less than 30 mA. If the current limit circuit shorted out, the current is limited to about 100 mA. • Input Channel Isolation Each channel is galvanically isolated from all other channels and earth (ground). The module/TA withstands, without damage, a potential of 600 V ac applied for one minute between any channel and ground, or between a given channel and any other channel. DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH This does not imply that these channels are intended for permanent connection to voltages of these levels. Exceeding the limits for input voltages, as stated elsewhere in this specification, violates electrical safety codes and may expose users to electric shock. Failure to follow these instructions will result in death or serious injury. 6 PSS 41H-2S201, Rev A Functional Specifications FBM201/b/c/d Analog Input (0 to 20 mA, 0 to 100 mV, 0 to 5 V, 0 to 10 V dc) Power Requirements • Input Voltage Range (Redundant): 24 V dc +5%, -10% • Consumption: 7 W • Heat Dissipation: 3 W (maximum) Calibration Requirements Calibration of the module and termination assembly is not required. Regulatory Compliance: Electromagnetic Compatibility (EMC) • European EMC Directive 2004/108/EC (Prior to April 20, 2016) and 2014/30/EU (Beginning April 20, 2016): Meets: EN61326-1:2013 Class A Emissions and Industrial Immunity Levels Regulatory Compliance: Product Safety • Underwriters Laboratories (UL) for U.S. and Canada: UL/UL-C listed as suitable for use in UL/UL-C listed Class I, Groups A-D; Division 2; temperature code T4 enclosure based systems when connected to specified Foxboro DCS processor modules. Communications circuits also meet the requirements for Class 2 as defined in Article 725 of the National Electrical Code (NFPA No.70) and Section 16 of the Canadian Electrical Code (CSA C22.1). For more information, see Standard and Compact 200 Series Subsystem User's Guide (B0400FA). • European Low Voltage Directive 2006/95/EC (Prior to April 20, 2016) and 2014/35/ EU (Beginning April 20, 2016) and Explosive Atmospheres (ATEX) directive 94/9/ EC (Prior to April 20, 2016) and 2014/34/EU (Beginning April 20, 2016): DEMKO certified as Ex nA IIC T4 for use in certified Zone 2 enclosure when connected to specified processor modules as described in the Standard and Compact 200 Series Subsystem User's Guide (B0400FA). RoHS Compliance Complies with European RoHS Directive 2011/65/EU, including amending Directives 2015/863 and 2017/2102. Marine Certification ABS Type Approved and Bureau Veritas Marine certified for Environmental Category EC31. | | |
易卖工控网供应商瑞昌明盛进出口贸易有限公司为您提供02-321145C03-504013模块备件的详细产品价格、产品图片等产品介绍信息,您可以直接联系商家获取02-321145C03-504013模块备件的具体资料,联系时请说明是在易卖工控网看到的。