¥ 1495.00
¥ 1495.00
¥ 1495.00
¥ 1495.00
¥ 1495.00
易卖工控网(www.ymgk.com)提供”JANCD-MTU01-486138模块备件”,产品详情:品牌/厂家:AZOP-005-486936、型号:JANCD-MTU01-486138、成色:全新、货期:现货 1天内发货、保修:180天,更多产品详情就上易卖工控网。
JANCD-MTU01-486138
要在DX200上使用JANCD-YEW01-E板,输入/输出模块必须
按照以下步骤进行设置。
检查以确保DX200的电源已关闭。
然后,安装JANCD-YEW01-E板,其所有开关
正确设置到DX200机柜内部。安装板时,
请参阅第4章“电路板安装”。
1、按住[主菜单],然后打开电源。
–主菜单显示。
2、选择主菜单下的{系统}。
3、将安全模式设置为“管理模式”。
补充资料
设置输入/输出模块时,将安全模式设置为
管理模式。
当安全模式设置为操作模式时
或编辑模式,只能参考设置状态
收件人:•检查以确保没有任何问题(损坏、弯曲等)
电路板的组件。
未遵守此注意事项可能导致人身伤害或
设备因故障损坏。
•正确连接电缆和连接器。
不遵守此警告可能导致火灾或设备故障。
•确保正确设置开关等。
未遵守此注意事项可能导致人身伤害或
设备因故障损坏。
•不要直接接触电路板的组件安装表面
用手指。
不遵守此注意事项可能导致IC等故障。
因为静电。
•不要用手指直接接触电路板的焊接表面。
不遵守此注意事项可能导致人身伤害
JANCD-MTU01-486138
JANCD-MTU01-486138
To use the JANCD-YEW01-E board on the DX200, the I/O module must
be set according to the following procedure.
Check to be sure that the power supply of the DX200 is turned OFF.
Then, install the JANCD-YEW01-E board all of whose switches are
properly set to the inside of the DX200 cabinet. When installing the board,
refer to chapter 4 “Board Installation” .
1. Press and hold [MAIN MENU], and turn ON the power.
– The Main Menu is displays.
2. Select the {SYSTEM} under the Main Menu.
3. Set the security mode to the “Management Mode”.
SUPPLEMENT
When setting the I/O module, set the security mode to the
management mode.
When the security mode is set either to the operation mode
or the editing mode, only the setting status can be referred
to. • Check to be sure that there is no problem (damage, bend, etc.) with
the components of the board.
Failure to observe this caution may result in personal injury or
equipment damage because of malfunction.
• Connect the cables and connectors properly.
Failure to observe this caution may result in fire or equipment failure.
• Make sure to properly perform the setting of the switches, etc.
Failure to observe this caution may result in personal injury or
equipment damage because of malfunction.
• Do not touch the component-mounting surface of the board directly
with a finger.
Failure to observe this caution may result in the failure of IC, etc.
because of static electricity.
• Do not touch the solder surface of the board directly with a finger.
Failure to observe this caution may result in personal injury