AS-BDEP-296模块全新现货

易卖工控网（www.ymgk.com）提供”AS-BDEP-296模块全新现货”，产品详情：品牌/厂家：、型号：AS-BDEP-296、成色：全新、货期：现货 1天内发货、保修：180天，更多产品详情就上易卖工控网。

同样的方式再建一个PC STATION，即为“PC2”.

16.jpg

7)、点击“Configure Network”按钮，进入NetPro 配置窗口。在NetPro 网络配置中，用鼠标选择“PC1” “OPC Server” 后在连接表一行鼠标右键插入一个新的连接或通过“Insert>NewConnection”也可建立一个新连接。

如果在同一STEP 7 项目中，所要连接的PLC 站已经组态完成，即PLC 以太网通讯处理器（CP343-1 or CP443-1）网络已经使能，在选择“Insert NewConnection”后，连接会自动创建，需确认连接属性即可。

17.jpg

18.jpg

8）、在NetPro 网络配置中，用鼠标选择“PC2” > “OPC Server” 后在连接表一行鼠标右键插入一个新的连接或通过“Insert>New Connection”也可建立一个新连接（与PC1的设定一样）。

9）、确认所有配置后，已建好的S7 连接会显示在连接列表中。点击编译存盘按钮或选择Network>Save and Compile，如得到No error 的编译结果，则正确组态完成。这里编译结果信息非常重要，如果有警告信息（Warning）显示在编译结果对话框中，这仅仅是一条信息。但如果有错误信息（errorMessage），说明组态不正确，是不能下载到PC Station 中的。

22.jpg

10）、完成PC 站组态后，即可在NetPro 窗口点击功能按钮栏中下载按钮将组态下载到PC站中。需注意的是，下载过程中会删除已有相关组件的数据，新的组态数据将被下载到PC 机。点击OK 执行下载。下载完成后，可以打开Station Configuration Editor 窗口检查组件状态。下图为正确状态显示画面。OPC Server 插槽Conn 一栏一定要有连接图标，此项说明连接激活。

此时，另一台电脑的设定如下，终状态也应如下图

须把IP地址设置正确。

打开Station Configuration Editor，配置PC站的硬件机架，其步骤与“二、配置PC 站的硬件机架”一致，应注意的是槽位与S7 MANEGER 的PC STATION站中PC2站一致。

配置控制台（Configuration Console）的使用与设置与步骤“三、配置控制台（Configuration Console）的使用与设置”一致。

In the same way, create another PC station, namely "PC2"
16.jpg
7) Click the "configure network" button to enter the netpro configuration window. In netpro network configuration, after selecting "PC1" and "OPC server" with the mouse, right-click to insert a new connection in the first row of the connection table or establish a new connection through "insert>newconnection".
If in the same step 7 project, the PLC station to be connected has been configured, that is, the PLC Ethernet communication processor (CP343-1 or cp443-1) network has been enabled. After selecting "insert newConnection", the connection will be automatically created. You need to confirm the connection attribute.
17.jpg
18.jpg
8) In netpro network configuration, after selecting "PC2 > OPC server" with the mouse, right-click to insert a new connection in the first row of the connection table or establish a new connection through "Insert > new connection" (the same as the setting of PC1).
9) . after confirming all configurations, the established S7 connection will be displayed in the connection list. Click the compile save button or select network>save and compile. If the compilation result of no error is obtained, the correct configuration is completed. The compilation result information is very important here. If a warning message is displayed in the compilation result dialog box, it is only a message. However, if there is an error message, it indicates that the configuration is incorrect and cannot be downloaded to PC station.
22.jpg
10) After completing the configuration of the PC station, click the download button in the function button bar in the netpro window to download the configuration to the PC station. It should be noted that the data of existing relevant components will be deleted during the download process, and the new configuration data will be downloaded to the PC. Click OK to execute the download. After downloading, you can open the station configuration editor window to check the component status. The following figure shows the correct status display. The conn column of OPC server slot must have a connection icon, which indicates that the connection is activated.
At this time, the settings of the other computer are as follows, and the final status should also be as follows
The IP address must be set correctly.
Open the station configuration editor and configure the hardware rack of the PC station. The steps are consistent with "II. Configure the hardware rack of the PC station". It should be noted that the slot position is consistent with the PC2 station in the PC station of S7 manager.
The use and setting of configuration console are consistent with step "III. use and setting of configuration console".