¥ 1495.00
¥ 1495.00
¥ 1495.00
¥ 1495.00
¥ 1495.00
易卖工控网(www.ymgk.com)提供”JANCD-FC008-486598模块备件”,产品详情:品牌/厂家:AZOP-005-486936、型号:JANCD-FC008-486598、成色:全新、货期:现货 1天内发货、保修:180天,更多产品详情就上易卖工控网。
JANCD-FC008-486598
•在执行之前,执行以下检查程序
机械手教学。如果发现问题,请进行维修
立即,并确保所有其他必要的处理
已执行。
–检查操纵器移动是否存在问题。
–检查外部电线的绝缘和护套是否损坏。
•始终将编程挂件返回到DX200上的挂钩上
使用后的机柜。
如果将编程挂件留在
操纵器的工作区域,在地板上或夹具附近。
•阅读并理解
操作操纵器前的DX200指令。
•接线和安装必须由授权或认证的人员执行
全体人员
不遵守此注意事项可能导致火灾或触电。
•检查确保没有异物(金属件等)
在黑板上。
未遵守此注意事项可能导致人身伤害或
设备因故障损坏。
•检查以确保没有任何问题(损坏、弯曲等)
电路板的组件。
未遵守此注意事项可能导致人身伤害或
设备因故障损坏。
•正确连接电缆和连接器。
不遵守此警告可能导致火灾或设备故障。
•确保正确设置开关等。
未遵守此注意事项可能导致人身伤害或
设备因故障损坏。
•不要直接接触电路板的组件安装表面
用手指。
不遵守此注意事项可能导致IC等故障。
因为静电。
•不要用手指直接接触电路板的焊接表面。
如果不遵守此注意事项,可能会导致人身伤害,因为
焊料突出等。
•避免电击板。
如果不遵守此注意事项,可能会导致电路板出现故障。
JANCD-FC008-486598
JANCD-FC008-486598
• Perform the following inspection procedures prior to conducting manipulator teaching. If problems are found, repair them immediately, and be sure that all other necessary processing has been performed. – Check for problems in manipulator movement. – Check for damage to insulation and sheathing of external wires. • Always return the programming pendant to the hook on the DX200 cabinet after use. The programming pendant can be damaged if it is left in the manipulator’s work area, on the floor, or near fixtures. • Read and understand the Explanation of the Warning Labels in the DX200 Instructions before operating the manipulator. • Wiring and installation must be performed by authorized or certified personnel. Failure to observe this caution may result in fire or electric shock. • Check to be sure that there is no foreign matter (metal piece, etc.) on the board. Failure to observe this caution may result in personal injury or equipment damage because of malfunction. • Check to be sure that there is no problem (damage, bend, etc.) with the components of the board. Failure to observe this caution may result in personal injury or equipment damage because of malfunction. • Connect the cables and connectors properly. Failure to observe this caution may result in fire or equipment failure. • Make sure to properly perform the setting of the switches, etc. Failure to observe this caution may result in personal injury or equipment damage because of malfunction. • Do not touch the component-mounting surface of the board directly with a finger. Failure to observe this caution may result in the failure of IC, etc. because of static electricity. • Do not touch the solder surface of the board directly with a finger. Failure to observe this caution may result in personal injury because of solder projection, etc. • Avoid shock on the board. Failure to observe this caution may result in the failure of the board.