¥ 800.00
¥ 888.00
¥ 666.00
¥ 1000.00
¥ 888.00
易卖工控网(www.ymgk.com)提供”主板DSDO115A DSAI146使用数量现货”,产品详情:品牌/厂家:、型号:DSAI146、成色:全新、货期:现货 1天内发货、保修:180天,更多产品详情就上易卖工控网。
.用于高强度结构粘合剂、油漆、氧化膜、油、灰尘、脱模剂等
其他表面污染物必须彻底清除。表面处理量
取决于用户要求的粘结强度、耐环境老化性。对于
建议在普通基板上进行表面处理,请参阅表面处理部分。
2.混合
用于Duo-Pak墨盒
3米™ 结构胶™ 丙烯酸粘合剂DP805和DP820采用双注射器供应
塑料duo-pak墨盒是3M的一部分™ EPX敷贴器系统。要使用,只需插入
将duo-pak药筒插入EPX治疗探头中,并使用
轻轻按一下扳机。接下来,取下duo-pak盒盖并排出少量
确保duo-pak墨盒的两侧均匀自由地流动。如果
如果需要自动混合A部分和B部分,请将EPX混合喷嘴连接到duo-pak
然后开始分配粘合剂。对于手动混合,排出所需量的
粘合剂和充分混合。在获得均匀颜色后约15秒混合。
散装集装箱
按重量或体积,按产品标签或包装上规定的比例充分混合
典型的未固化属性部分。均匀着色后约15秒搅拌
获得。
3.为了获得大粘合强度,在要接合的两个表面上均匀涂抹粘合剂。
4.对于Scotch Weld丙烯酸树脂,应在2分钟内涂抹到基材上
粘合剂DP805或透明焊接丙烯酸粘合剂15分钟
. For high strength structural bonds, paint, oxide films, oils, dust, mold release agents and all other surface contaminants must be completely removed. The amount of surface preparation depends on the required bond strength, environmental aging resistance desired by user. For suggested surface preparations on common substrates, see the section on surface preparation. 2. Mixing For Duo-Pak Cartridges 3M™ Scotch-Weld™ Acrylic Adhesives DP805 and DP820 are supplied in a dual syringe plastic duo-pak cartridge as part of the 3M™ EPX Applicator System. To use, simply insert the duo-pak cartridge into the EPX applicator and start the plunger into the cylinders using light pressure on the trigger. Next, remove the duo-pak cartridge cap and expel a small amount of adhesive to be sure both sides of the duo-pak cartridge are flowing evenly and freely. If automatic mixing of Part A and Part B is desired, attach the EPX mixing nozzle to the duo-pak cartridge and begin dispensing the adhesive. For hand mixing, expel the desired amount of adhesive and mix thoroughly. Mix approximately 15 seconds after uniform colour is obtained. For Bulk Containers Mix thoroughly by weight or volume in the proportions specified on the product label or in the typical uncured properties section. Mix approximately 15 seconds after uniform color is obtained. 3. For maximum bond strength, apply adhesive evenly to both surfaces to be joined. 4. Application to the substrates should be made within 2 minutes for Scotch-Weld acrylic adhesive DP805 or 15 minutes for Scotch-Weld acrylic adhes